Fitting In And Removal From The Car; With The Isofix Fastening; With Isofix Fastening And Toptether Anchoring - Volkswagen Bobsy G1 ISOFIX DUO plus TopTether Bedienungsanleitung

3

Fitting in and removal from the car

Note
Before mounting the child safety seat, this should be brought to the sitting position (see 7).
3.1

with the ISOFIX fastening

After adjusting the child safety seat shoulder belts (see 5.1) as follows, secure it with ISOFIX:
- Clip both guides* (Fig. A, No. 10) on to both ISOFIX anchorage points on the car seat, between the seat squab and the
backrest. There must be a clearly audible "click". The recess of the guide must be visible from above (Fig. K).
- Using the grip provided for this purpose (Fig. A, No. 8), pull out both armrests (Fig. A, No. 11) to the full extent. On
both sides of the seat squeeze the locking button (Fig. A, No. 13) and the red release button (Fig. A, No. 12) together
and remove the connector protection. The lock (Fig. A, No. 9) in both mounts (Fig. A, No. 11) must be open (Fig. L).
- Position both mounts (Fig. A, No. 11) directly in front of the guides (Fig. A, No. 10).
- As the mount on the first side engages (Fig. A, No. 11), there must be a clearly audible "click" (Fig. M).
- As the mount on the other side engages (Fig. A, No. 11), there must also be a clearly audible "click" (Fig. M).
- To release the locking mechanism turn the green lever (Fig. B, No. 27) downwards. Then push the child seat with the
lever (Fig. B, No. 27) turned down towards the backrest.
- Push the child seat towards the backrest applying firm, even pressure on both sides (Fig. N).
- Check that the seat is firmly in position by pulling on each side.
- To release the ISOFIX fastening (dismounting), press the green securing knob (Fig. A, No. 13) and the red slide (Fig. A,
No. 12) against each other, first on one side, then on the other (Fig. O). Release the mounts (Fig. A, No. 11).
* The guides simplify fitting ISOFIX in some cars and avoid damaging the seat. They should be fitted where necessary and, if they are not
used, they should be removed and stored in a safe place. In vehicles with folding backrests, the guides must be removed before folding.
Defects can generally be attributed to dirt in the guides and the catches in the mounts. This can generally be put right by removing the dirt.
3.2

with ISOFIX fastening and TopTether anchoring

After adjusting the child safety seat shoulder belts (see 5.1) as follows, secure it with ISOFIX and TopTether:
- Clip both guides* (Fig. A, No. 10) on to both ISOFIX anchorage points on the car seat, between the seat squab and the
backrest. There must be a clearly audible "click". The recess of the guide must be visible from above (Fig. K).
- Using the grip provided for this purpose (Fig. A, No. 8), pull out both armrests (Fig. A, No. 11) to the full extent. On
both sides of the seat squeeze the locking button (Fig. A, No. 13) and the red release button (Fig. A, No. 12) together
and remove the connector protection. The lock (Fig. A, No. 9) in both mounts (Fig. A, No. 11) must be open (Fig. L).
- Position both mounts (Fig. A, No. 11) directly in front of the guides (Fig. A, No. 10).
- Now take the TopTether (Fig. A, Pos. 2) out of the bag that is on the top of the rear side of the seat shell (Fig. A, Pos. 1).
- Lift the metal tongue (Fig. Z
(Fig. Z , No. 3) to a V-shape.
2
- Place the strap behind the vehicle seat.
Engage ISOFIX:
- As the mount on the first side engages (Fig. A, No. 11), there must be a clearly audible "click" (Fig. M).
- As the mount on the other side engages (Fig. A, No. 11), there must also be a clearly audible "click" (Fig. M).
- To release the locking mechanism turn the green lever (Fig. B, No. 27) downwards. Then push the child seat with the
lever (Fig. B, No. 27) turned down towards the backrest.
- Push the child seat towards the backrest applying firm, even pressure on both sides (Fig. N).
- Check that the seat is firmly in position by pulling on each side.
Anchor TopTether:
- Open the spring hook (Fig. Z
- Attach the spring hook (Fig. Z
Z ) or behind the backrest (Fig. Z
5
Note
Please observe the recommendations of your vehicle manual. Do not modify your vehicle by drilling or bolting
something in. Never fasten the TopTether to a location which has not been recommended by the vehicle manu-
facturer. If the TopTether comes loose in a crash, there is a danger of injury to the vehicle passengers.
- Tighten the belt (Fig. Z
- To release the TopTether anchoring loosen the belt (Fig. Z
adjuster away from the belt. Then take the spring hook (Fig. Z
- To release the ISOFIX fastening (dismounting), press the green securing knob (Fig. A, No. 13) and the red slide (Fig. A,
No. 12) against each other, first on one side, then on the other (Fig. O). Release the mounts (Fig. A, No. 11).
* The guides simplify fitting ISOFIX in some cars and avoid damaging the seat. They should be fitted where necessary and, if they are not
used, they should be removed and stored in a safe place. In vehicles with folding backrests, the guides must be removed before folding.
Defects can generally be attributed to dirt in the guides and the catches in the mounts. This can generally be put right by removing the dirt.
, No. 1) away from the strap (Fig. Z
2
, No. 3) by pressing with your thumb against the spring clip.
2
, No. 3) to the appropriate anchorage point (on the rear shelf (Fig. Z
2
)) - see vehicle manual.
6
, Pos. 1) of the TopTether, by pulling its free end firmly in the direction of the arrow.
3
13
, No. 2) and pull the strap out with the spring hook
2
, No. 2) by lifting the metal tongue (Fig. Z
2
, No. 3) out of the anchoring point.
2
) or on the floor (Fig.
4
, No. 1) of the
2