Fitting The Hand Spray Gun, The Jet Pipe And The Nozzle; Operation; Checking The Oil Level Of The Engine; Bleeding The Oil Tank - Parkside PHDB 4 B2 Originalbetriebsanleitung

Fitting the hand spray gun, the jet pipe and the
nozzle
DANGER!
► Risk of injury! Appliance, supply pipes, high-pressure hose and
connections must be in perfect working order. If the equipment is
not in perfect working order, the appliance may no longer be used.
♦ Connect the jet pipe to the hand spray gun
♦ Tighten the screws of the jet pipe
♦ Fit the nozzle onto the jet pipe
correctly.
♦ Fit the high-pressure hose

Operation

Checking the oil level of the engine

■ Check the oil level before each use.
■ Do not use the appliance if there is no oil visible on the dipstick
■ Add oil as required. Use only engine oil (15W40).
♦ Place the appliance on a flat, level surface and remove all dirt from
around the oil inlet/dipstick
♦ Use the dipstick to measure the oil level.
Unscrew the dipstick and wipe it clean with a cloth.
Put the dipstick back into the oil inlet without screwing it in.
back out and check the oil level.
Pull the dipstick
♦ Check that the oil level is somewhere between the minimum and max-
imum levels (marked as L for low and H for high on the dipstick
♦ To fill up the oil, take the supplied funnel
into the oil inlet . Do not overfill!
♦ Wait a minute until the oil has settled before measuring the oil level
again as described above.
♦ Screw the dipstick back into the oil inlet.
PHDB 4 B2
.
by hand.
. Ensure that it clicks into place
onto the hand spray gun .
.
MAX.
MIN.
and pour the oil slowly
CAUTION!
► Do not overfill the oil. A too high oil level can cause engine damage.
The maximum fill level for the tank is 0.6 litres.
NOTE
► The engine is equipped with an oil level sensor. The oil level sensor
switches the engine off if the oil level is too low and prevents a
restart. If the engine cuts out although the oil level is correct, check
whether the petrol-powered high-pressure cleaner is standing straight.

Bleeding the oil tank

CAUTION!
► Before first use, the bleed valve on the oil tank needs to be replaced.
On delivery, a black transport oil plug
be replaced by the supplied red oil plug

Engine

Observe the section "Safety instructions"!
.
■ Before use, read the manufacturer's operating instructions and pay
close attention to the safety instructions.
■ Checking the oil level of the engine.
Do not use the appliance if the oil level has fallen below "MIN".
■ Add oil as required.
■ Fill the fuel tank
Do not use a 2-stroke mixture.

Adding fuel

DANGER! RISK OF FIRE AND EXPLOSION!
).
► Never refuel in confined spaces or when the engine is running
or still hot.
► Do not smoke while refuelling.
► Do not use any 2-stroke mixture.
► Do not refuel in the vicinity of open flames or sparks.
► Do not spill fuel – use a funnel.
► Wipe up any spilt fuel.
► After refuelling, close the fuel canister and the tank properly.
♦ Fill the fuel tank
♦ Add fuel up to the red mark.

Water connection

See technical specifications for the connection data.
■ Connect the supply hose (minimum length 7.5 m, minimum diameter
3/4") to the water connection on the appliance and to the water
supply (e.g. tap).
■ Turn on the water supply.
NOTE
► The water supply hose is not included in the delivery.

Drawing water out of a container

DANGER!
► Never draw water from a drinking water container.
Never prime with liquids containing solvents such as paint thinners,
petrol or oil. Atomised spray from solvent is highly flammable,
explosive and toxic.
♦ Connect the suction hose
(accessories) to the water connection
is screwed in which has to
.
with unleaded petrol.
with unleaded petrol.
(diameter at least 3/4") with the filter
.
GB │ MT │
29 ■