Introduction; Intended Use; Residual Risks; Features - Parkside PHDB 4 B2 Originalbetriebsanleitung

PETROL PRESSURE WASHER PHDB 4 B2

Introduction

Congratulations on the purchase of your new appliance. You have chosen
a high-quality product. The operating instructions are a part of this product.
They contain important information about safety, usage and disposal.
Before using the product, please familiarise yourself with all operating and
safety instructions. Use the product only as described and for the range of
applications specified. Please also pass these operating instructions on to
any future owner.

Intended use

This appliance is designed for cleaning:
machines, vehicles, buildings, tools, façades, terraces, garden equipment,
etc.
–
for low-pressure cleaning with a cleaning agent (e.g. cleaning machines,
vehicles, buildings, tools),
–
for high-pressure cleaning without a cleaning agent (e.g. cleaning
façades, terraces, garden equipment).
Self-priming when using alternative water sources
This appliance is self-priming and allows the suction of water from containers
and natural sources. It is IMPORTANT that the filter on the water inlet is
cleaned and in place, and that only clean water is sucked in.
Any other use that is not expressly permitted in these operating instructions
may damage the appliance and represents a serious risk for the user.
Please make sure that you pay attention to the restrictions in the safety
instructions. Pay attention to the national regulations which may restrict the
use of the machine.
Any other uses of or modifications to the machine are deemed to be
improper usage and may result in serious physical injury.
Not intended for commercial use.
DANGER!
► Risk of injury! When using at petrol filling stations or other danger
areas, comply with all corresponding safety regulations.
NOTE
► Waster water that is contaminated with oil should not be released
into the soil, open water or down drains. Therefore, only wash engines
and vehicle underbodies at suitable sites that have oil separators.
CAUTION! Water quality requirements:
■ Only clean water may be used as a high-pressure medium. Contam-
ination can lead to premature wear or residues in the appliance. If re-
cycling water is used, the following thresholds may not be exceeded.
│ GB │ MT
■ 20
pH value
Electrical conductivity*
Settleable solids**
Filterable substances***
Hydrocarbons
Chloride
Sulphate
Calcium
Overall hardness
Iron
Manganese
Copper
Active chlorine
Free of unpleasant odours
*Maximum in total 2000 μS/cm
**Sample volume 1 l, sedimentation time 30 min
***No abrasive substances

Residual risks

CAUTION!
■ Even if used correctly, it is not possible to exclude non-apparent
residual risks entirely.
■ Injuries due to slipping on waste water.
Injuries or property damage due to the high-pressure water jet.

Features

High-pressure hose
Quick connector
Hose holder
Nozzles (red, yellow, green, white, black)
Air filter
Filler cap
Fuel tank
Tubular frame
Filler cap for cleaning agent tank
Cleaning agent tank
Cleaning agent hose
Rubber feet
Lower spray gun holder
Tyres
Oil drain screw
Jet pipe
Pull starter
Hand spray gun
Upper spray gun holder
Trigger
Trigger lock
Exhaust silencer
Wing nut
Choke
Fuel tap
Spark plug/Spark plug connector
Carburettor
6.5...9.5
Conductivity
Fresh water
+1200 μS/cm
< 0.5 mg/l
< 50 mg/l
< 20 mg/l
< 300 mg/l
< 240 mg/l
< 200 mg/l
< 28 °dH
< 50 °TH
< 500 ppm
(mg CaCO /l)
3
< 0.5 mg/l
< 0.05 mg/l
< 2 mg/l
< 0.3 mg/l
PHDB 4 B2