Vector Control - Lenze 8200 motec Montageanleitung

Commissioning

Vector control

4.5 Vector control
The following instructions apply to controllers equipped with a standard−I/O function module and a
three−phase AC motor which has been selected according to a power−based assignment.
1. Connect the keypad
2. Ensure that controller inhibit is active after mains connection
3. Switch on the mains
4. The keypad is in "Disp" mode after approx. 2 s and indicates
the output frequency (C0050)
5. Go to the menu
ALL
f
6. Change to the
your drive
7. Adapt the terminal configuration to the wiring (C0007)
Lenze setting: −0−, i. e.
E1: JOG1/3 fixed setpoint selection
E2: JOG2/3
E3: DCB DC injection brake
E4: CW/CCW rotation
8. Set the minimum output frequency (C0010)
Lenze setting: 0.00 Hz
9. Set the maximum output frequency (C0011)
Lenze setting: 50.00 Hz
10. Set the acceleration time T
Lenze setting: 5.00 s
11. Set the deceleration time T
Lenze setting: 5.00 s
12. Activate the control mode "vector control" (C0014 = 4)
Lenze setting: Linear V/f characteristic control (C0014 = 2)
13. Adapt the voltage/current range for the analog setpoint
selection (C0034)
Lenze setting: −0−, (0 ... 5 V/0 ... 10 V/0 ... 20 mA)
14. Enter the motor data
A) Rated motor speed (C0087)
Lenze setting: 1390 rpm
B) Rated motor current (C0088)
Lenze setting: Depends on the controller
C) Rated motor frequency (C0089)
Lenze setting: 50 Hz
D) Rated motor voltage (C0090)
Lenze setting: Depends on the controller
E) Motor−cosj (C0091)
Lenze setting: Depends on the controller
94
efesotomasyon.com - Lenze
mode to configure the basic settings for
(C0012)
ir
(C0013)
if
EDK82MV752 DE/EN/FR 6.0
}
X3
Terminal X3/28 = LOW
20 28
misc001
ON
misc002
d c b e a
The
1
Πj g f k i h PS
0050
000
‚
m n o
p
000
q r
Hi
Hz
Lo
z
d c b e a
Blinking on the display:
w x 1
Œ
j g f k i h PS
0050
000
y ‚ m n o
p
000
q r
Hi
Hz
Lo
z
d c b e a
1
w x Πj g f k i h PS
0007
000
‚
m n o
p
y
0
q r
Hi
Lo
[f]
C0011
C0010
0 %
100 %
f [ H z ]
C 0 0 1 1
f 2
t = acceleration time wanted
ir
f 1
0
t
t i r t i f
T i r T i f
t = deceleration time wanted
if
d c
1
Œ
f 00 14
Set Disp Subcode Para H/L PS
000
p
4
z
w x
y
E82ZBC014
z
d c b e a Set the DIP switch on the standard I/O to the
w x 1
Πj g f k i h PS
0034
000
‚ m n o
y p
0 same range (see Mounting Instructions for the
q r
Hi
standard I/O)
Lo
See motor nameplate
Enter the value for the motor connection type
(star/delta) selected!
Enter the value for the motor connection type
(star/delta) selected!
USEr menu is active
0050
C0011
+ t @
T
f 2 * f 1
ir ir
C0011
+ t @
T
if if f 2 * f 1
L