Owner's Guide; Safety Precautions; Unpacking; Set-Up And Assembly - Coltene Coltolux Led Benutzerhandbuch

Owner's Guide

CAUTION: Federal law restricts this device to sale by or on the
order of a licensed healthcare practitioner.
Congratulations...
...on your purchase of the Coltolux
Coltolux LED combines a slim curing probe with high output in a
®
cordless lightweight pen-style design . The Coltolux
technology reduces the amount of heat emission and eliminates the
need for a fan . LED light output matches the absorbtion spectrum
of Camphorquinone (CQ) photoinitiators .
Indications for Use
The Coltolux LED is indicated for the polymerization of intra and
®
extra oral restorations fabricated from materials (commonly referred
to as visible light cured dental restoratives and/or composites and/or
dental adhesives) that contain Camphorquinone as the photoinitiator .
See Figure 1 and Figure 2 for component recognition .
Fig. 1.
a. Handpiece
b. Handpiece Charger Base
c. Activation Button
Fig. 2.
d. Voltage/Serial Number Label
e. Power Cord with Power Supply
f. Plug Adapters (Export Only)
g. Light Shield
h. Test Block,
i. Barrier Sleeves
j. Light Lenses
Please take special note of the safety precautions below.
I. SAFETY PRECAUTIONS
A. Observe the following precautionary procedures before and
whenever using the Coltolux
Before connecting, read all instructions .
Persons having a history of photosensitive
reactions or who are using photosensitizing
drugs should not be exposed to light from
this unit.
Explosion hazard. Do not use in the presen-
WARNING
ce of flammable anesthetics.
Do not operate the Coltolux
the light lens in place and fully seated on the
unit (Fig 4) as this may impair patient safety..
Never modify the power cord. Modifications
to the power cord may result in an electric
shock hazard.
WARNING
Do not refrigerate or put in freezer to cool.
This may result in damage to the unit.
Use of a power supply other than that listed
in section XIV. Accessories may result in
CAUTION increased electromagnetic emissions and/or
decreased electromagnetic immunity.
B. All high intensity lights may cause retinal damage with
prolonged exposure to the eyes, therefore we urge you observe
these cautionary statements:
LED Curing Light . The
®
LED's heat sink
®
LED Curing Light .
®
LED without
®
Never look directly into the light emitted from
the light lens or reflected from tooth or other
surfaces as retinal damage may occur.
WARNING
• Patients, operators and dental technicians should always
use proper eye protection .
• Always use light shields (Cat . No . C7990) available for light
curing or use eye protection goggles (Cat . No . C7988) that
block light in the blue spectral range . Sunglasses are not
adequate protection .
• A barrier sleeve should be used for every patient (Cat . No .
C7957) . Slide the barrier sleeve over the handpiece and
then attach the light shield .
• Before each use, inspect the light lens (Section IX) .
C. The Coltolux LED is an electrical appliance requiring proper
®
disposal according to local laws and regulations .
II. UNPACKING
• Before unpacking, examine the carton for external damage,
and if severe, contact your shipper/carrier .
• Open carton and carefully remove the unit and accessories .
Make sure supply voltage is within the range specified on
the power supply (Fig . 3) . If not, do not operate this unit;
contact your dealer or Coltène/Whaledent Inc .
III. SET-UP AND ASSEMBLY
• Coltolux LED is designed as a cordless handpiece unit
®
with a separate charger base . Place the charger base on a
smooth flat surface in an area that is dry and free of dust,
is convenient and has an outlet within easy reach of the
supplied power cord . Export units include additional plug
adapters (Fig . 2F) . Install the appropriate plug adapter onto
the power supply (Fig . 3) .
• Remove the protective insert by first sliding the release but-
ton in the direction indicated by the arrow . Hold the button
in this position while removing the insert from the supply .
• Angle the top of the new adapter into the recess of the sup-
ply . Slide the release button in the direction indicated while
simultaneously pressing the new adapter into place .
Please Note: Additional plug adapters are not supplied for
Australian and New Zealand markets. Plug the power cord into
the wall outlet and then into the charger base. A green light
on the charger base indicates power is available to charge the
handpiece.
• Insert the handpiece into the charger base . When the han-
dpiece is being charged, the light on the charger base will
be orange . When the handpiece is fully charged and ready,
the orange light on the charger base will turn green .
The initial charging of the handpiece will require approxima-
tely 3 hours to fully charge .
• When the handpiece is removed from the charger base the
small light above the On/Off button on the handpiece will be
green, indicating the unit is ready for use . If the light does
not light up green, see Section VII Troubleshooting .
3