3M PROTECTA Rebel 3100418 Bedienungsanleitung Seite 9

3.0 INSTALLATION
3.1 PLANNING: Plan your fall protection system before starting your work. Account for all factors that may affect
your safety before, during, and after a fall. Consider all requirements and limitations defi ned in Section 2.
IMPORTANT: In most applications, the Rebel SRL can be connected to the anchorage or the harness
Dorsal location. Either orientation is allowed.
3.2 ANCHORAGE:
Figure 6 illustrates typical SRL anchorage connections:
A Anchorage
Select an anchorage location with minimal free fall and swing fall hazards (see Section 2). Select a rigid
anchorage point capable of sustaining the static loads defi ned in Section 2.3. Rebel SRLs must always be
anchored at or above the user's Dorsal D-Ring.
IMPORTANT: It is recommended that this equipment be installed under the supervision of a qualifi ed
person.
3.3 HARNESS MOUNTING OPTIONS:
Single SRL Full Body Harness Mounting: The Rebel SRL can be connected to the harness dorsal D-Ring
with a Carabiner or Snap Hook. (See Figure 8, connection examples 1 and 2). Some Rebel models include a
Carabiner. All include a Snap Hook.
Connect the Swivel Eye (Rebel components identifi ed in Figure 2) to the D-Ring on the harness using the
Carabiner included with some Rebel models (or use a suitably rated connector), or use the included Snap
Hook to connect to the D-Ring. The opposite end of the Rebel must be connected to an anchorage point (see
Section 2.3) with an included Carabiner (or a suitably rated connector), or the included Snap Hook.
Twin SRL Harness Mounting using a Carabiner: Some Rebel SRL models include a Carabiner (identifi ed
in Figure 2) which can connect two Rebel SRLs to a Full Body Harness when climbing applications require
100% tie-off. The Carabiner mounts two Rebel SRLs side-by-side just below the harness Dorsal D-Ring. (See
Figure 8, connection example 3)
To mount two Rebel SRLs on a Full Body Harness with the Carabiner: (See Figure 7. A - Web Straps;
B - Dorsal D-Ring; C - Swivel Eye, SRL)
Step 1: Loosen the Harness Webbing: Pull out on the Web Straps (A) where they pass through the
bottom of the Dorsal D-Ring (B) until there is suffi cient space to slide the Carabiner between the
Web Straps and D-Ring Pad.
Step 2: Open the Triple-Action Carabiner: Lift up on the Carabiner Gate (1) and twist it 45 degrees
(2) to align the slot in the gate with the Carabiner frame. Push the Gate (3) inward to open the
Carabiner.
Step 3: Mount the fi rst Rebel SRL on the Carabiner: Insert the Carabiner through the Swivel Eye (C)
on the SRL.
Step 4: Insert the Caribiner through the Web Straps: With the Carabiner Gate held open, insert the
Carabiner behind the Web Straps. Rotate the Carabiner behind the Web Straps until the Carabiner
surrounds the the Web Straps and the fi rst Rebel SRL is positioned on the right side of the
Carabiner.
Step 5: Mount the second Rebel SRL on the Carabiner: Insert the Carabiner through the Swivel Eye
on the second SRL. Position the second SRL on the left side of the Carabiner Gate.
Step 6: Allow the Carabiner Gate to close and lock.
Check the mounting of both SRLs: When properly mounted, the Carabiner should pass through the Web
Straps (A) and the SRL Swivel Eyes should be secured on either side of the Carabiner Gate. Pull the Web
Straps (A) back through the Dorsal D-Ring and D-Ring Pad to eliminate slack in the webbing and secure the
Carabiner between the Web Straps and D-Ring Pad.
B Connector C Tie-Off Adapter
9