Pioneer F-Z4GO0L Bedienungsanleitung Seite 32

TIMER PLAYBACK
If the timer doesn't operate
When checking the timer, if you press TIMER ON/OFF switch and the
timer indicator goes off, that timer will not operate.
The timer setting is memorized, so if you check the timer setting again
and make sure the indicator lights with TIMER ON/OFF switch, it will
operate.
Precautions concerning the timer
1. If you don't perform the next operation within a few seconds of
pressing TIMER PGM switch, timer mode is canceled, returning you
to frequency display.
2. You can perform timer setting even if power is on STANDBY.
3. If you press a day selection switch twice, the day is canceled.
4. If you have selected tape playback:
¢ Playback starts in the same direction (<1 or &) the tape was
playing just before the power was cut.
© If only one deck is loaded with a tape, playback begins on that
deck.
¢ If both Deck | and Deck II are loaded with tapes, relay playback
starts on Deck I.
5. With EVERY and ONCE selection, if you select ONCE, the timer will
only operate once. The setting is still memorized, however, so if you
make sure the timer indicator lights using TIMER ON/OFF switch
when checking the timer settings, it will operate again.
6. If the ON time and OFF time settings are the same on a single timer,
no operation will occur.
7. The timer will not operate unless power is on STANDBY.
8. If MUTING is ON, even if the timer operates, there will be no sound.
The SNOOZE function
If you press SNOOZE key on the remote control unit after the timer has
started operating, power will be cut for about five minutes, and then
it will switch on again. If there are less than five minutes of timer
operation remaining, when you press SNOOZE key, power will remain
cut, and timer operation will finish.
TIMER RECORDING (Recording using the weekly timer)
(Use tuner for timer setting)
This system is equipped with three timers (TIMER 1 to 3). You can use
each of these for play and recording (Example: TIMER 1: Play, TIMER
2: Play, TIMER 3: Record).
At the set time power will switch on, and recording will start. If the timer
clock isn't set, timer operation will not occur, even though the timer
can still be set.
(Example) If you use TIMER 3.
(See page 8, Fig. .)
1. Set the cassette deck to record standby.
@) Load the deck with the cassette to be recorded on.
© If you want to copy a tape, load Deck | with the tape you want
to copy, and Deck II with the tape you want to record on.
(For CT-Z460WR]
© If you only want to record on Deck II, load it with a tape.
¢ If you want to perform relay recording or parallel recording, load both
decks with a tape to record on.
If you select TAPE II or RELAY, carry out the necessary procedures
for recording and record in the direction displayed (<1 or >). If you
select PARALLEL, recording will start in the forward direction (> ),
so be careful you load the tape correctly.
[For CT-Z36OWR] -
The display indicates the direction (<I or E) in which recording
will start on DECK Il.
32
<ARE1137>
En
(@) Select REV MODE switch (0.
(3) Set DOLBY NR switch (3 to the desired position.
(4) Press REC ( @) switch @).
() Adjust the recording level with REC LEVEL control (2.
(©) Press STOP switch @).
2. Set the timer.
3. Set the timer start time.
4. Set the timer stop time.
Procedures 3, 4, and 5 are the same as TIMER PLAYBACK procedures
2, 3, and 4, so refer to page 31 before setting.
5. Select timer recording.
@ Use ''—'' and '+' switches @ to set to ''REC''.
(2) Press SET/NEXT switch (1).
ta
6. Select the recording source with ''-"' and ''+'
switches (2).
The recording source changes each time ''—'' and "' +"' switches
are pressed. The recording source changes in the following order
when "' +' switch is pressed.
i TUNER — CD — TAPE— PHONO — |
VCR «—-LD
Select TUNER, CD, or TAPE.