Pioneer F-Z4GO0L Bedienungsanleitung Seite 26

!
|
i
1
!
| {
BASIC OPERATIONS
Auto Stop Mechanism
The mechanism stops automatically when the end of tape is reached.
NOTE:
® When the PLAY switch of one deck is pressed while the other deck
is in playback mode, the former stops and the latter starts playback.
¢ When playing back a tape you have recorded on, you'll get a better
sound if you play it back on the same side you recorded it on. (For
example, if you record on a cassette inserted with the A side facing
outwards, you should also have the A side facing outwards when
you play it back.)
¢ /f the power is cut when the tape is moving, the cassette door may
not open. If this happens, turn on the power once more, and press
EJECT switch.
. © Press EJECT switch after you have checked that the deck has stopped
operating.
Counter switch
The counter functions as a normal tape counter and also as a time
counter, displaying elapsed time. Use this switch to select either of these
two functions.
The tape counter only displays information for the deck the tape is
inserted in. If tapes are inserted in both decks, only information
concerning the deck with the tape inserted last is displayed information.
e When there are tapes in both decks, use the I/Il switch (1) to select
which deck's counter display you want to see.
¢ Select between tape counter and time counter using the TIME switch
[DEKT (DECK IT}
Li
al
-, =,
ans
mas ~~, ~~, aan -, =
—_ a ~— 'om, "ame son "ame, a
rm
TT
"Ll
"om. a
onl
'a
—,
@).
Tape counter display Time counter display
CORT IGT eea Rae,
"an amasl
fe
— 'od
Ir
'a,
<coaae, iaricgs fi
Indicates elapsed time
during tape travel.
~~ anak
rm
L
— anal ~— 'on,
bi
_ ~~
Numbers change to indicate
how far the tape has travelled.
¢ Press RESET switch © to reset the counter.
NOTE:
¢ The time counter only displays elapsed time during recording and
playback. If you fast forward during either, the time counter stops,
and it switches to the tape counter. During music search, it changes
to P-xx display. (Numbers are displayed in xx). lf you start recording
or playback again, the time counter will resume operating.
© When recording from a CD or other source, the time counter on the
deck and the time display on the CD player or other source may show
Slightly different values.
RECORDING ONTO A CASSETTE TAPE
(Cassette deck operation)
You can record on DECK II of the CT-Z36OWR.
You can record on both DECK | and DECK II of the CT-Z460WR.
If you turn on the graphic equalizer then you can record the equalized
sound (The graphic equalizer doesn't operate if the stereo amplifier's
DIRECT switch is ON). This explanation concerns DECK I! but the same
procedure also applies to operating DECK | of the CT-Z460WR.
1. Press EJECT switch, and load the tape for recording into Deck Il.
* Check to see that the accidental erasure prevention tabs are not
broken off.
e Make sure that there is no tape slack.
26
<ARE1137>
En
2. Set DOLBY NR switch (3 to the desired position.
e A tape which has been recorded using the DOLBY NR system
must be played back with the same system ''ON"'.
3. Select REV MODE switch (0.
To perform reverse recording, use the cu> or => . And be sure
to start recording in the forward direction (>).
4. Use the input selector switch on the amplifier to select and play
the recording source.
Play a tape in the digital
Digital audio tape
audio tape deck
Video disc sound Play a video disc
VCR sound Play a tape in the VCR
5. Adjust sound quality with the graphic equalizer.
6. Press REC ( @) switch @).
e You're now in pause ready to record.
¢ The REC indicator lights.
e The play indicator (<1 or -) flashes.
7. Adjust recording level with REC LEVEL control (12.
e Adjust so that OdB on the level meter lights. It doesn't matter if
+ 6dB lights momentarily.
8. Press PAUSE ((1) or the appropriate PLAY (>, <1) switch @).
9. To stop recording, press STOP ( 1) switch @).
NOTE:
e The input selector cannot be switched during recording.
e Sound quality cannot be altered with the graphic equalizer during
recording.
e When listening to a CD or DAT, the sound is not affected by the
graphic equalizer if DIRECT switch is ON.
¢ During recording and playback, the way the level meter lights may
differ depending on the sensitivity of the tape. Small differences,
however, don't cause any problems.
Auto reverse function
This unit uses rotary type recording and playback heads, and the same
heads are used in both forward and reverse directions. Tape end
detection is employed to activate auto reverse operation which takes
approx. 2 seconds after the tape is taken up.
NOTE:
A leader tape having a length equivalent to approx. 5 seconds is
attached to an ordinary cassette tape. This means that for two-way
travel of the leader tape there will be a break of approx. 12 seconds
in the sound. Be very careful of this, particularly when making a two-
way recording.
Pausing and restarting recording
1. Press PAUSE (()0) switch @).
¢ Recording will be suspended.
2. To restart recording again, press PAUSE ({]]) switch @).