Pioneer F-Z4GO0L Bedienungsanleitung Seite 29

PARALLEL RECORDING (Only the CT-Z460WR has this function)
With this function, both decks start recording the same source at the
same time. Both decks must be in stop mode.
1. Load Deck I and Deck Il with tapes to be recorded to.
Make sure there is no tape slack.
¢ Parallel recording begins from the forward direction (—).
. Set DOLBY NR switch (3) to the desired position.
. Select REV MODE switch (0.
WN
the recording source.
5. Adjust the recording level.
@) Press REC ( @) switch @) on Deck I or Deck Il.
@) Adjust the recording level with REC LEVEL control (1).
(3) Press STOP ((] }switch.
6. Press PARALLEL switch @).
¢ Deck | and Deck II will both start recording in the forward direction.
7. To stop recording, press STOP(()switch @) on either Deck I or
Deck Il.
e Both decks will stop.
. Use the input selector switch on the amplifier to select and play
NOTE:
¢ /f the accidental erasure prevention tabs of the side A on either tape
cassette are broken off, recording will not begin when PARALLEL
Switch is pressed.
© After beginning recording, temporary stop (00), mute (Q), and stop
(C0) operate on both decks at the same time.
e During reverse recording, when the head rotates while the leader tape
is moving, recording temporarily stops.
e /f you use tapes of different length, recording stops when the shortest
tape ends, so it is recommended you use tapes of the same length.
RELAY RECORDIN G (Only the CT-Z4G0WR has this function)
With this function, deck Il starts recording when deck | finishes
recording. Both decks must be in stop mode.
1. Load Deck | and Deck II with tapes to be recorded to.
e Make sure there is no tape slack.
® In Deck Il, recording will be performed in the direction that is
presently indicated ( <1 or & ), so make sure the tape is loaded
correctly.
2. Set DOLBY NR switch (3 to the desired position.
3. Select REV MODE switch (10.
==. : When recording finishes on one side of the tape in Deck |,
recording will start on one side of the tape in Deck Il.
=> or c> : When relay recording finishes on Deck |, relay
recording starts on Deck II. If recording starts in the
<1 direction, however, the tape doesn't reverse (the
tape doesn't reverse from <I to > on either of the
decks).
GRAPHIC EQUALIZER CONTROL
4. Use the input selector switch on the amplifier to select and play
the recording source.
. Press REC ( @ ) switch @) on Deck |
. Adjust the recording level with REC LEVEL control @.
. Press the appropriate PLAY (<1 or >) switch @) on Deck I.
e Recording starts on Deck |.
8. Press RELAY/SKIP switch (2).
9. To stop recording, press STOP ((_)) switch on the deck recording.
¢ If you press STOP switch during recording on Deck I, RELAY/SKIP
indicator stays lit.
"© O61
To use the graphic equalizer, first set the BASS control and TREBLE
control to the center (flat) position of the amplifier.
1. Turn on EQUALIZER switch (0.
e Press so that EQUALIZER indicator lights.
2. Use EQUALIZING CONTROL switches ©) to adjust sound.
e Left and right channels are adjusted simultaneously.
How to recall a factory preset equalization curve.
This unit has five factory presets.
HEAVY: for rock and other popular music; emphasizes bass and treble.
CLEAR: for electronic music, fusion, and other genres where you want
a clear sound with strong midrange and treble characteristics.
SOFT: _ ideal when listening to such genres as background music for
extended periods of time.
VISUAL: ideal when enjoying a movie or sports programs, where you
want a sound field with strong midrange and treble
characteristics.
VOCAL: acurve for listening to vocals including operas and musicals.
1. Turn on EQUALIZER switch (0.
2. Use PRESET/PGM switch (i6 to select PRESET.
e Press so that PRESET indicator lights.
3. Press a memory recall switch (5 for the preset curve you wish to
recall.
NOTE:
The presets change in the following order when you are operating with
a remote control unit.
[ HEAVY— CLEAR— SOFT— VISUAL— a
E <-D <-C «-B —PROGRAM A
e Even in the spectrum analyzer display mode, equalization display is
shown a few seconds after operation of EQUALIZING CONTROL
switches.
/t isn't possible to change equalization characteristics during recording.
© The audio signals from the DAT AUDIO OUT and VCR AUDIO OUT
are not equalized.
29
<{ARE1137>
En