Pioneer F-Z4GO0L Bedienungsanleitung Seite 10

CONNECTIONS
Basic Setup
See page 3, Fig. for the connections diagram.
@ Accessory AM loop antenna
(@) Accessory FM antenna
FM/AM tuner (F-Z460L/F-Z460)
Speaker
Stereo amplifier (A-Z460 or A-Z360)
Graphic equalizer (GR-Z460)
Double cassette deck (CT-Z36OWR or CT-Z460WR)
Compact disc player (optional PD-Z560T or PD-Z960M)
Optical cable
Input/Output cable (Flat cable)
Power cord
AC wall socket
QOGCEQOOHO
Plug the power cord into the AC wall socket outlet only after all the
connections have been completed.
Proceed as follows with the connections:
1. Connect the supplied AM loop antenna (1) and FM antenna @ to
the FM/AM tuner.
2. Connect the FM/AM tuner input/output cable to the amplifier
TUNER jack.
Connecting the input/output cable
See page 4, Fig. j
Match the colors on the plug with those on the jack and insert. Never
remove or insert the plug when the power is switched on. Push the
plug in straight until both the left and right pins lock. To remove,
hold both sides of the plug and pull out slowly.
3. Connect the compact disc player input/output cable to the amplifier
CD jack.
4. Connect the compact disc player optical output jack to the amplifier
optical input terminal with the optical cable. (See page 4, Fig. [6] )
Remove the dust cap, align the plug and the terminal, and insert.
@) Dust-cap
(2) Terminal
(3) Optical cable
CAUTIONS FOR HANDLING OPTICAL CABLE
A. Do not fold optical cable when using as the cable is easily
damaged. When circling it, keep the diameter of the loop greater
than 15 cm.
. When connecting it, insert the plug firmly to the end to prevent
a faulty connection.
. Prevent the plug of the optical cable from getting scratched or
dusty. If dusty, clean with a soft cloth before connecting.
. When the optical cable is not connected, use the dust-cap on
the optical terminal of the unit to avoid dust.
5. Connect the cassette deck input/output cable to the amplifier
CASSETTE TAPE DECK jack.
6. Connect the graphic equalizer input/output cable to the amplifier
GRAPHIC EQUALIZER jack.
7. Connect the speakers using the speaker cords.
Connect the ''+'' terminals on the amplifier to the '' +'' terminals
on the speakers, and the '' —"' terminals on the amplifier to the ''—"'
terminals on the speakers.
10
<{ARE1137>
En
@
- @) Push the speaker terminal knob down.
(2) Insert the speaker cord.
(3) Push the knob up.
@t te
NOTE:
Do not allow the conductors of the cords to project beyond the terminals
and to come into contact with other conductors. A breakdown or failure
may occur when conductors touch one another.
Speaker impedance
Connect speaker systems with a nominal impedance of between 6 and
160.
8. Finally, connect the power cord (11)
Connecting other components
NOTE
e Insert the plugs securely into the jacks. Improper connection can lead
to sound distortion or malfunctioning.
¢ Connecting a stereo turntable
See page 4, Fig. :
Stereo amplifier
Turntable
Power supply cord (Connect this if you're using a PONEER PL-Z460
or PL-Z560)
Ground cord ( Connect this if you're using anything other than a
PIONEER PL-Z460 or PL-Z560)
® ©80
If using this unit together with PIONEER PL-Z460 or PL-Z560, connect
the turntable's audio cords and power supply cord respectively to the
amplifier's PHONO jacks and DC 12V OUTPUT jack.
If using a different turntable, connect the audio cord and ground cord.
¢ Connecting a Video Disc Player
See page 5, Fig. :
@ Stereo amplifier
@) Audio cord
@) Videodisc player (LD player)
¢ Connecting a VCR
See page 5, Fig. [9] '
(@) Stereo amplitier
(@) VCR
@ Audio cord
¢ Connecting a Digital Audio Tape deck (DAT)
See page 6, Fig. :
@ Stereo amplifier
@) Digital audio tape deck
@) Coaxial cable with pin plug
() Audio cord
¢ Connecting Surround Speakers (rear speakers)
See page 6, Fig. :
@ Stereo amplifier
@) Surround speaker (left channel)
(3) Surround speaker (right channel)
Connect a speaker system having a normal impedance of 16 Q or
more.