Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Determining the soft water capacity
Determine the water hardness of the
raw water using a hardness measuring
device (order no. 6.768-003.0) or ask
your provider.
Read soft water capacity in the follow-
ing table.
Water
WS 50
hardness
Capacity
° dH
m
3
5
10,0
10
5,0
12
4,2
14
3,6
16
3,1
18
2,8
20
2,5
22
2,3
The output can be shown via the dial
gauge.
Dial gauge
The dial gauge automatically switches on
as soon as water flows.
By shortly pushing the button you can
switch between the different displays.
The following can be shown on the display
of the dial gauge:
Volume counter 1
–
shows the generated quantity of soft
water in litres
Note: The volume counter is reset by
pushing the button for at least 2 sec-
onds.
Volume counter 2
–
Note: Both volume counters can indi-
vidually be reset.
Automatic
–
Flow volume
–
shows the current flow rate in litres/min.
Note: The display switches between li-
tres/min and gal/min when pushing the
button for at least 2 seconds.
Regeneration
There are 2 ways to determine the deple-
tion of the soft water:
via the indicator of the volume counter
–
on the display of the dial gauge.
by measuring the water hardness at the
–
soft water outlet by means of the hard-
ness measuring device for soft water
(order no. 6.768-004.0).
Regenerating depleted plant
There are 2 ways to regenerate the plant.
If a WS regenerator is available: Con-
–
nect the plant to the WS regenerator.
See operating instructions of the WS re-
generator for description.
Replace resin filling in the tank (exchanger).
–
Replacing the resin filling in the tank (ex-
changer).
Depressurize the system.
Remove the hose from the soft water
connection.
Remove connection hose filter/tank.
Release the tie down strap and remove
WS 100
unit from the frame.
Capacity
Loosen and screw out the tank adapter
m
3
using the key.
20,0
Pull the rising pipe out of the tank.
Turn the tank around and collect the
10,0
resin in a suitable container.
8,3
Flush tank with water.
7,1
Fill in new resin (order no. 6.761-031.0
6,3
- 25 kg).
5,6
Note: Use a funnel for filling, flush resin
5,0
in with water.
4,5
WS 50 - 12.5 litres
WS 100 - 25 litres
After the resin has been filled in, fill the
tank completely with water.
Insert the rising pipe in the tank (do not
use tools), fill with water and simultane-
ously push it down carefully until it
reaches the bottom.
Note: Ensure that the rising pipe is in
the centre of the tank.
Reassemble the plant in reverse order.
Maintenance and care
Danger
Risk of injury!
Always wear protective goggles when op-
erating, maintaining and cleaning the appli-
ance.
The plug connections are under pressure,
depressurise the plant prior to detaching
the plug connections.
Caution
Risk of damage! Drain the tank if there is a
risk of frost.
Draining the tank if there is a risk of frost
1 Drain valve
2 Transport rails
Remove the hose between the filter and
the tank and let it drain.
Open and drain the filter.
Remove the hose from the soft water
connection.
Tip the unit onto the transport rails.
General notes
Risk of frost
3
-
EN
Open the drain valve on the hose.
Note: Bring the valve as far as possible
below the tank, this facilitates the drain-
ing of the water in the tank.
If the water is drained, the plant is save to
be exposed to frost.
Maintenance Works
Daily checks prior to operation
Check plant for leaks.
–
Check battery status (battery status in-
–
dicator in the display dial gauge), re-
place if necessary. Battery type
CR2032.
Check tie down strap, replace as nec-
–
essary.
Check the soiling of the candle, replace
–
as necessary (order no. 6.761-361.0).
Maintenance every 3 months
Lubricate wheel bearing.
–
Check hoses and couplings for dam-
–
age.
Troubleshooting
No soft water
Plant depleted
If a WS regenerator is available: Con-
nect the plant to the WS regenerator
and regenerate it.
Replace resin filling in the tank (ex-
changer).
Resin leakage
Lower nozzle on the rising pipe defec-
tive
Replace the nozzle.
Leakage
Connecting adapter not properly tight-
ened
Tighten adapter using key.
Seal defective
Check and replace.
7
Werbung
