Product Description; Intended Use; Prerequisites For Operation With Fsa; Hardware - Bosch FSA 500 Originalbetriebsanleitung

3.

Product description

3.1

Intended use

The FSA 500 is a portable diagnostic device for use in
motor vehicle workshops.
The FSA 500 is suitable for the checking of vehicles
with spark ignition, Wankel and diesel engines and
can be used for testing all the electrical and electronic
systems on passenger cars, commercial vehicles and
motorcycles.
The FSA 500 picks up vehicle-specific signals and
relays them via Bluetooth or the USB interface
to e.g. DCU 120, DCU 220 or a PC/laptop (not
included in the scope of delivery). The software
FSA 500 CompacSoft [plus]must be installed for this.
!
The FSA 500 is not suitable for use as a measuring
instrument for test drives.
!
The maximum permissible measurement voltage
at the Multi measurement inputs is 200 V. FSA 500
is therefore not to be used for measuring isolation
from the supply on electric and hybrid vehicles.
FSA 500 CompacSoft [plus] features the following
functions:
R
Motor vehicle identification
R
Settings
R
Test steps for checking spark-ignition and diesel
engines
R
Multimeter measurements for voltage, current and
resistance
R
Signal generator (e.g. for testing sensors)
R
Component test (checking of vehicle components)
R
Characteristic curve tracer
R
4-channel/2-channel universal oscilloscope
R
Primary ignition oscilloscope
R
Ignition oscilloscope Secondary
R
Insulation measurements with FSA 050 (special
accessory)
For the assessment of measurement results,
confirmed "go" measurement curves can be stored as
reference in the quantity measurement system.
Robert Bosch GmbH
Product description | FSA 500 | 21 |
3.2 Prerequisites for operation with
FSA 500 CompacSoft [plus]
3.2.1

Hardware

DCU 120, DCU 220 or PC/laptop required.
Minimum requirements for PC/laptop
R
Operating system: Windows 10
R
CPU (processor): 2 GHz or more
R
RAM (working memory): 4 GB or more
R
Free disk space (SSD or HDD): 5 GB or more
R
USB ports (USB 2.0 or USB 3.0): A USB interface
for the Bluetooth USB adapter or the USB
connection cable
3.2.2

Software

Current version of FSA 500 CompacSoft [plus]
installed on DCU 120, DCU 220 or PC/laptop.
i
For control unit diagnostics with CAS[plus], the
current ESI[tronic] software (info type SD) must be
installed and licensed on the PC/laptop. Control
unit diagnosis is possible only with a KTS module.
This is subject to additional cost.
3.3

Scope of delivery

Designation
FSA 500
Power supply unit
with power supply cable
USB connection cable (3 m)
Battery B+/B– cable
Clip-on sensor
Primary connecting cable, term. 1/15
CH1 multi measurement cable
CH2 multi measurement cable
Amps clamp 1000 A
Coupling with hose assembly
Remote trigger
Secondary measuring sensor
passenger car oil temperature sensor
Measurement cable with voltage divider
Test prods
Alligator clip, black
Accessory set with
Black and red test prods
Black and red pick-off clips
Black, red, gray adapter connectors
Bluetooth USB adapter
Case
Important information and safety
instructions
Operating instructions
en
Order number
–
1 687 023 814
1 684 461 106
1 684 465 562
1 684 460 286
1 687 225 018
1 684 461 185
1 684 460 288
1 684 460 289
1 687 225 019
1 686 430 053
1 684 463 828
1 687 225 017
1 687 230 068
1 687 224 301
1 683 050 050
1 684 480 022
1 687 016 118
1 687 023 777
1 685 438 644
1 689 979 922
1 689 989 411
|
1 689 989 411 2023-03-24