Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
(EN)
INSTRUCTION MANUAL
WARNING: READ ALL INFORMATION CONTAINED IN THE TWO INSTRUCTIONS: GENERAL
AND SPECIFIC.
SPECIFIC INSTRUCTIONS
Before using the Personal Protection Equipment (PPE) you must read carefully and understand
the safety information described on general instruction and the specific equipment instructions.
ATTENTION!!! If you have any doubt about the product, if you need others language version of
the instructions for use, declarations of conformity or any question about the PPE, please contact
us: www.fallsafe-online.com.
WARNING: The manufacturer and the seller decline any responsibility in case of incorrect use,
improper application or modifications/ reparations by persons not authorized by FALL SAFE®.
1 – PHYSICAL CONDITION AND TRAINING:
Work at height are potentially dangerous and it must only be used by professionals and experien-
ced persons. Before using the PPE you must be aware of: your mental and physical condition; be
trained for the use of the device; do not have any doubt about using the equipment and the field
of application.
WARNING: the equipment shall only be used by a person trained and competent in its safe use.
WARNING: the consumption of alcohol, medicine or any other type of psychotropic will influence
your balance, concentration conditional and must be avoided.
2 – BEFORE USE:
For your safety it is strictly recommended that you always check your device and equipment
before, during and after use and that you regularly submit your device and equipment to
inspections and controls by competent persons, every 12 months at the latest. These time
intervals may change according to frequency and intensity of device and equipment use. The
FALL SAFE INSPECTOR® allows you to easily record and access information on inspections,
inventory and use. It tracks equipment assignments by worker or location and automates the
inspection process. There are multiple system options available that allow for easy-access and
time-saving information.
Every time before use, check (visually and tactile) the condition of the equipment components:
textile material (straps, ropes, stitching) must not show any signs of abrasion, fraying, burns,
chemical or cuts. The metal material (buckles, carabiners, hooks, cable and metal rings) must not
show any signs of wear, corrosion, deformation or defects and should operate correctly.
WARNING: is essential for safety that equipment is withdrawn from use immediately should:
1) Any doubt arise about its condition for safe use or;
2) Is have been used to arrest a fall and not used again until confirmed in writing by a competent
person that it is acceptable to do so;
For you safety read all contained information on this general instructions, as well as the specific
instructions accompanying the device and make sure that you understand them; ensure the
equipment conditioning and all recommendation of security; ensure that the components are
compatible with each other and be sure if are fulfilled with the rules, regulations and directives;
ensure an emergency plan, check the work safety conditioning and confirm all system are
assembled correctly without interfering with each other.
WARNING: use of combinations of items of equipment in which the safe function on any one item
is affected by or interferes with the safe function of another.
WARNING: that a rescue plan shall be in place to deal with any emergencies that could arise
during the work.
WARNING: Remind to check the limitation and the devices compatibility. Remember that the
ropes have different particularities and can be changed according the weather conditioning. The
manufacture declines any responsibility for accidents, injuries or death due to improper and
incorrect use by the user, all other usage procedures must be considered forbidden. The
equipment shall not be used outside its limitations, or for any purpose other than that for which it
is intended.
WARNING: it is essential for safety to verify the free space required beneath the user at the
workplace before each occasion of use, so that in the case of a fall, there will be no collision with
the ground or other obstacle in the fall path.
As the name suggests, the PPE is for personal use. In exceptional case using by a second user,
carry out a check of the equipment before and after usage and if possible take note of the
relevant date.
WARNING: never use a PPE without knowing the provenance, or neither if the inspection records
are not updated as it is issued.
All the materials and treatments used are antiallergenic; they should not cause skin irritations or
sensitivity. The connectors are made of steel, zinc plated; light alloy, polished or anodized:
stainless steel, polished.
WARNING: during the use avoid the following hazards that may affect the performance of the
equipment: extremes of temperature, trailing or looping of lanyards or lifelines over sharp edges,
chemical reagents, electrical conductivity, cutting, abrasion, climatic exposure and pendulum
falls.
3 – MARKING
WARNING: Never remove or damage de labels and marking; after use check if they are legible.
The following information is etched on the device: CE marking; (Number of the production
process controlling body); Name of the manufacturer or of the person responsible for the product
introduction on the market; standard (number and year of the standard; the logo that warns the
user to carefully read the user instructions attached to the product; production lot number; year
of production; maximum load applicable in kN, the strength indicated is the lowest value
guaranteed by the producer. The marking on the device are indicated in different places
depending on the dimension. See more detailed in "Specific Instructions".
WARNING: Check the markings are legible even after use.
WARNING: it is essential for the safety of the user that if the product is re-sold outside the original
country of destination the reseller shall provide instructions for use, for maintenance, for periodic
examination and for repair in the language of the country in which the product is to be used.
4 – LIFE TIME
It is rather difficult to establish the length of the device's life, as it can be adversely affected by
several negative factors such as intensely frequent or improper use; the conditions the device is
required to work in (humid, freezing and icy conditions); wear; corrosion; serious stress with or
without relative deformation; exposure to heat sources; improper storage; device age; exposure
to chemical agents... (plus any further reason, not merely limited to all the foregoing reasons).
Taking the adequate care of your device (please consult the "Maintenance") will have a
considerable influence on and will definitely increase device durability and long life. By the way
of example, the following can be considered as a rule to determine standard potential durability
of devices, tools and equipment: ten years for fall protection harness, fall protection vests/jacket-
s/ coveralls, accessories (lanyards, foot loop, suspension trauma and relief strap) anchor lines,
anchor straps, ropes, carrying bags, fall arrest webbing blocks and sharp edge tested; eight
years for equipment conditioned to extreme environments (harness, lanyards, vests, jackets and
coveralls); undefined for connectors, descenders, rope clamps, rope grabs, pulleys, anchor
points; especially 10 years (5 in stock – 5 in use) for gloves and helmet . It is nevertheless
EN
CS
HU
PL
RO
SK
s g
SPECIFIC INSTRUCTIONS
DA
NO
SV
FI
PT
ES
recommended that you replace your devices, tools and equipment at least every 10 years,
considering that in the meantime new techniques or regulations may have become applicable
and your equipment may no longer be compliant and/or compatible with one another.
WARNING: The lifetime of an equipment can be limited in case of severe falls, extreme tempera-
tures, contact with harmful chemicals, sharp edges and the absence of markings or labels.
5 – ELIMINATION/ DISPOSAL CONSIDERATIONS
You should dispose of the equipment if: the lifetime has been exceed; if you suspect that the
equipment is not safe; if it is obsolete (incompatible with modern equipment or that do not
conform to the standards updates); if it has been in a fall event (see the fall arrest indicator was
violated); if it is over than 10 years.
The materials used in the equipment production may cause environmental impacts. For this
purpose it is recommended that the equipment are disposed of in accordance with the laws in
force in the country where the disposal is taking place.
WARNING: The equipment which is not in operable condition or used in a fall event must be
destroyed immediately.
6 – REPARATION
ATTENTION!!! Any modification on the product void the guarantee and can compromise the
user´s safety. The possibility of re-using the device must be authorized exclusively by the
producer with a prior written consent that reserves the right to carry out appropriated examina-
tions and testing. Only the manufacture or authorized staff can make the repairs and tampering.
7 – MAINTENANCE, CLEANING AND INSPECTION
Check before, after and during use that the equipment works properly. If you need wash the
components use clean water with a small amount of neutral soap to remove persistent dirt or if
the purpose is disinfect dissolve a disinfectant which contains quaternary ammonium salts in
warm water (max. 20ºC), soak the equipment in this solution for one hour. Rinse with potable
water and leave them to dry out in the open air protected from sunlight.
WARNING: when the equipment becomes wet, either from in use or when due to cleaning, I shall
be allowed t dry naturally, and shall be kept away from direct heat.
If you need to lubricate the metal components you must use only silicone based oil spray.
WARNING: Remove the excess oil and check that if the lubrication don't interferes the interaction
between the device, others components of the system and the user's.
For your safety it is therefore highly recommended that submit your device and equipment to
inspections and controls by competent persons, every 12 months at the latest. These time
intervals may change according to frequency and intensity of device and equipment use. If you
ever have even the smallest doubt as to the condition of the device, please contact us: www.fall-
safe-online.com. The FALL SAFE INSPECTOR® allows you to easily record and access
information on inspections, inventory and use. It tracks equipment assignments by worker or
location and automates the inspection process. There are multiple system options available that
allow for easy-access and time-saving information.
WARNING: for regular periodic examination, and that the safety of users depends upon the
continued efficiently and durability of the equipment.
WARNNG: periodic examination are only to be conducted by a person competent for periodic
examination and strictly in accordance with the manufacture´s periodic examination procedures.
8 – STORAGE/ TRANSPORT
Remove the item from its container and store it in a cool, dry, well-aired place. There must not be
any corrosive, solvent substances or heat sources (max. 80°C/ 176°F) in the storage place.
The device must not come in contact with other sharp objects which can damage it. Never store
the equipment before having thoroughly dried it and avoid storing it in places with a high saline
concentration. Except for the above-mentioned indications, there are no special precautions to
be used during the transport. Avoid leaving your equipment in a car or in a closed placed exposed
to the sunlight.
9 – GUARANTEE
This product is provided with a three year warranty against any manufacturing defect, or defects
in the materials it is composed of. The warranty does not cover standard item wear, device
alterations, improper storage, damages due to improper use of the device, negligence, improper
maintenance, etc., and any further reason not only limited to the aforesaid.
ADDITIONAL INFORMATION
AI1 - Acceptable Temperature; AI2 - Storage; AI3 - Annual Inspection; AI4 - Cleaning; AI5 -
Drying; AI6 - Hazards; AI7 - Risk of death; AI8 - Attention; AI9 - Right; AI10 - Wrong; AI11 -
Check.
MARKING/ LABLES
ML(A) - Reference number; ML(B) - Manufacture date; ML(C) - Brand name; ML(D) -
Instructions; ML(E) - QR code;
EQUIPMENT RECORD
1-Product; 2-Reference Number; 3-Serial Number; 4-Manufacturing Date; 5-Purchase Date;
6-Date of first use; 7-Other relevant information; 8-Date; 9-Reason for entry; 10-Defects,Repair-
s,Etc; 11-Name & Signature; 12-Next periodic examination
NOMENCLATURE/FIELD OF APPLICATION
NFA1 - Webbing 25mm; NFA2 - Dyneema Rope; NFA3 - Storage Bag; NFA4 - Adjust Buckle;
NFA5 - Attachment Point; NFA6 - Webbing 44mm.
DONNING AND SETUP
DS(A) - BEFORE USE THE SAFE STEP MUST BE CONNECTED WITH A KARABINER OR
INTERLACED IN WORKING POSITIONING D-RIND OR VENTRAL D-RING; DS(B) - OPEN
THE SAFE STEP BAG; DS(C) - CONNECT THE BUCKLE IN THE WEBBING LOOP ACCOR-
DING YOUR LEG SIZE; DS(D) - CONNECT THE BUCKLE IN THE WEBBING; DS(E) - PUSH
THE WEBBING TO BE TAUT; DS(F) - USE THE BUCKLE THE ADJUST THE WEBBING; DS(G)
- ANCHOR THE SAFESTEP TO A SAFE ANCHOR POINT; DS(H) - ANCHOR THE SAFESTEP
TO A SAFE ANCHOR POINT AND CONNECT THE KARABINERS IN THE HOLES; DS(I) -
MAKE THE ADJUSTMENT PASSING THE ROPES IN THE HOLES; DS(J) - THE SAFESTEP
IT´S READY TO USE
(CS)
NÁVOD K POUŽITÍ
VAROVÁNÍ: PŘEČTĚTE SI VŠECHNY INFORMACE OBSAŽENÉ VE DVOU POKYNECH:
OBECNÉ A SPECIFICKÉ.
KONKRÉTNÍ POKYNY
Před použitím osobních ochranných prostředků (PPE) si musíte pozorně přečíst a porozumět
bezpečnostním informacím popsaným ve všeobecných pokynech a specifických pokynech k
zařízení.
FR
IT
DE
NL
ET
LV
LT
RU
BG
EL
HR
MT
4
SL
AR
Werbung
Inhaltsverzeichnis
