Parkside PBBPS 700 A1 Originalbetriebsanleitung Seite 19

10.1.1 Starting the motor when cold
m WARNING
Engage the chain brake before every start-up (push the front
hand guard (3) forward).
m ATTENTION
Never allow the start pull cord (8) to spin back. This can result
in damage.
1. Remove the guide rail cover (21).
2. Set the chainsaw down on a firm and level surface. The
saw chain (1) must not come into contact with the floor.
3. Push the front hand guard (3) forwards until it latches
into place. The saw chain (1) is clamped by the chain
brake.
4. Press the fuel pump primer (4) 6x. (Fig. 1)
5. Switch the ON/OFF switch (15) to "ON". (Fig. 1)
6. Pull out the cold start (choke) lever (14). (Fig. 10.2)
7. Hold the chainsaw firmly by the front handle (12) and
pull the start pull cord (8) out slowly until you feel the
first resistance.
8. Now pull the start pull cord (8) and the engine should
start. If the engine does not start, repeat the process. As
long as the cold start lever (choke) (14) is pulled out,
the engine will run for only a short time and then stop.
9. As soon as the engine has stopped, actuate the throttle
interlock (7) and the throttle (5) together. The cold start
(choke) lever (14) will automatically spring back to the
"warm start" operating position. (Fig. 10.1)
10. Now pull the start pull cord (8) again and the engine
should start.
If the engine does not start even after several attempts, read
the "Troubleshooting" chapter.
NOTE
With high outside temperatures, it may be necessary to start
the engine without the cold start lever (choke) (14) even when
the engine is cold!
• Release the chain brake by pulling the front hand guard
(3) backwards. (Fig. 2)
• CAUTION! The chain brake is now released. If the throt-
tle (5) is actuated together with the throttle interlock (7),
the saw chain (1) starts up.
10.1.2 Starting the motor when warm
(The device stood still for less than 15–20 minutes)
m WARNING
Engage the chain brake before every start-up (push the front
hand guard (3) forward).
1. Push the front hand guard (3) forwards until it latches
into place. The saw chain (1) is clamped by the chain
brake.
2. Switch the ON/OFF switch (15) to "ON".
3. The cold start lever (choke) (14) does not have to be
pulled to start a warm engine.
4. Hold the chainsaw firmly by the front handle (12) and
pull the start pull cord (8) out slowly until you feel the
first resistance.
5. Now pull the start pull cord (8) quickly. The device
should start after 1–2 pulls. If the device has still not
started after 6 pulls, repeat the procedure described
under "Starting the engine when cold".
10.2 Shutting the engine off
10.2.1 Emergency stop procedure
If it is necessary to stop the device immediately, set the ON/
OFF switch (15) to "OFF". (Fig. 1)
10.2.2 Normal procedure
1. Release the throttle (5). The engine goes into idle speed.
2. Then set the ON/OFF switch (15) to "OFF". (Fig. 1)
10.3 Operating while idle
m ATTENTION
When idling, the saw chain (1) must be stationary.
NOTE
If the saw chain (1) moves at idle or the engine stops on its
own when the throttle is released, a carburettor adjustment
must be made (see chapter "Maintenance of the carburettor
settings").
1. Pick up the chainsaw.
2. Use the left hand to hold the front handle (12) firmly.
3. Use the right hand to hold the rear handle (6) firmly. The
heel of the hand rests on the throttle interlock (7) and the
index finger operates the throttle (5).
4. After actuating the throttle (5) once, the engine runs at
idle.
5. Allow the engine to warm up briefly.
GB/IE/NI/CY/MT
13