Foreseeable Misuse; Personnel Qualifications; Information On Equipping The Door With A Drive - Novoferm iso45-5 TW Original-Montage- Und Betriebsanleitung

The product is not suited for being used by persons
(or children) with reduced physical, sensory or mental
capabilities or lack of experience and knowledge.
However, the door can be used within the reach of
children.
2.2

Foreseeable misuse

Any use other than described in chapter Intended use
is regarded as reasonably foreseeable misuse. This
particularly applies to the following cases:
• If the product is not used in accordance with the
intended purpose.
• If the product is used without regard to the
minimum level of safeguarding in accordance
with EN 12453.
• If the product has been improperly serviced or
maintained, by means of non-qualified persons.
• If loads exceeding the standard hand force affect
the door leaf (only open and close the door leaf
without loads, and do not intentionally counteract
the opening or closing process).
• Using drives that are not part of the system or
that are incorrectly adjusted.
• Adding or installing components and parts which do
not comply with the intended use to or in the door,
the locking system or the drive and / or performing
modifications to the original delivery state.
• If changes or modifications have been made on
the door or its components.
• In the event of failure to observe the assembly,
operation and maintenance instructions, the
respectively applicable country-specific norms or
applicable safety regulations.
• If the door is not in a perfectly safe condition.
• Door elements, drives and radio controls are not
a toy for children.
Door elements are not suited for being used as load-
bearing components. Either vertical or horizontal in-
stallation has to be performed in accordance with the
version. The rails are to be aligned perpendicularly or
according to the assembly specifications.
Any damage or injury as a result of reasonably fore-
seeable misuse and / or of not following the assembly
and operating instructions will render the manufac-
turer's liability null and void.
2.3

Personnel qualifications

The following persons are qualified to perform as-
sembly, disassembly, maintenance activities or to re-
place the torsion spring:
Qualified persons according to the EN 12604 and
EN 12453 requirements.
Competent persons are defined as persons who have
been given the necessary instructions and who are
by way of training and/or experience and knowledge
qualified and authorised to carry out the required
tasks correctly and safely.
These assembly, operation and maintenance instructions must be kept for the entire period of use!
The following persons are qualified to perform elec-
trical installation work and to work on the electrical
system:
• Qualified electricians
Skilled electricians must be able to read and under-
stand electric circuit diagrams, to put electrical sys-
tems into service and to maintain them, to wire con-
trol cabinets, to install the control software, to ensure
the functionality of electrical components and to
identify possible hazards resulting from handling elec-
trical and electronic systems.
The following persons are authorised to handle the
product:
• operating personnel
The operator must have read and understood the in-
structions, in particular the "Safety" chapter and must
be aware of the hazards associated with handling the
product.
2.4 Information on equipping the door with
a drive
If equipping this door with a Novoferm door drive ac-
cording to the enclosed Declaration of Performance
(R-500, N-423, N-563S, B-1200 or Novoport IV):
• In order to guarantee the performance
characteristics specified below, please consider
the additional information regarding assembly,
commissioning, operation and maintenance in
the door drive instructions.
If equipping this door with a door drive where the
brand name is not explicitly mentioned:
• The enclosed Declaration of Performance is not
fully applicable, e.g. information regarding
operating powers are to be certified by the
manufacturer of the door system by means of a
new and individual declaration of performance or
conformity.
• The door system must comply with all valid EU
directives (Machinery Directive, Low-voltage
directive, EMC directive etc.) and with all
applicable national and international norms and
regulations.
• The door system shall be marked by the
manufacturer with a rating plate and the CE
marking in compliance with the above-mentioned
Declaration of Performance. Moreover, a
handover documentation must be compiled in
your local language and kept safe by the
operator throughout the entire service life of the
door.
Bolt plates, bolt catches and bolt bars of the manually
operated door must be dismantled independently of
the selected door drive.
EN - 21