Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
4.4
Assembling the door frame
Please refer to the picture section of the assembly in-
structions, meanwhile, follow the illustrations as
shown in the instructions.
4.4.1 Preassembling the door frame
Place wood or similar underneath the angle
frames (1L/1R)
scratches.
Fig.
a
, page A3. Connect the angle frame (1L/1R)
with the frame panel (3) by screwing them together
with the metal screws (pre-assembled).
VL Fig.
b
Mount the sole plates (8L/8R) to the angle
frames (1L/1R) by screwing them together with the
screws (S11).
4.4.2 Mounting the wall anchors
Prior to mounting the wall anchors (7), check the
width stop and the place for the plugs on the ma-
sonry.
Depending on the stop width and the mounting condi-
tion, mount the wall anchors (7) by means of the
screws (S6 + S12) as follows:
Fig.
a
, page A3. The width stop exceeds 120 mm.
Place the wall anchors (7) on the outside of the angle
frame.
Fig.
b
The width stop's range is between 80 mm and
119 mm. Place the wall anchors (7) on the inside of
the angle frame.
Also observe the following:
Fig.
c
For mounting the horizontal rail pairs later on,
it is required to pre-assemble the connection
screw (S5). To do so, insert the screw (S5) through
the addendum angle of the frame (1L/1R) and secure
the screw from falling out by lightly screwing on the
nut (S12).
4.4.3 Mounting the plugs for the door frame
Fig.
a
, page A4. Set up the door frame and place
it behind the driveway opening.
Secure the door frame against toppling over and pre-
cisely align it angular and in parallel by using the
spirit level.
Fig.
b
Mount the shutter holder (13) by clipping it on
the centre of the shutter (3).
From a width of basic dimension = 3530 mm, 2 shut-
ter holders are included in the scope of delivery.
Mount them at regular distances.
Fig.
c
Pre-drill the holes for the plugs (Ø=10 mm)
with a depth of at least 65 mm (approx.). For this pur-
pose, it is best to use a rock drill with a length of
200 mm.
Fig.
d
, Fig.
e
and Fig.
plates (8L/8R), the shutter holder (13) and all angle
frames with the screws (S8) and the respective dow-
els (S9).
Fig.
g
For anchoring the frame to the ground, use
the screw (S8) in combination with the plug (S9) and
the washer (U1).
24 - EN
to
provide
protection
f
Screw together the sole
Fig.
h
Insert the screw (S6) into the lowest hole of
the angle frame (1L/1R) and fasten with the screw
nut (S12).
NOTICE
against
4.4.4 Preassembling the horizontal rail pairs
Fig.
a
, page A7. Connect the horizontal rail
pair (14L/14R) to the tail end (16L/16R) by using the
screw (S17).
Fig.
c
Mount the connecting plate (18) with the
screws (S6 and S12). In doing so, note that the screw
heads (S6) are mounted towards the inside to the rail!
Fig.
d
Mount one corner connection bracket (20)
each to the rail pair (14L/14R) with the screws (S11).
4.4.5 Mounting the horizontal rail pairs to the
frame
Fig.
a
and Fig.
pair (14L/14R) together with the screw that has
already been premounted on the angle frame (1L/1R)
by loosely screwing the rail pair to the tail
end (16L/16R) with the screw nut (S12). It should still
be possible to fold up the system later on.
Fig.
c
Fold up the horizontal rail pairs (14L/14R) and
secure them against folding back.
Fig.
d
, page A8. Mount the rail arches (30) by
screwing them to the angle frames and to the con-
necting plates (18) by means of the screws (S17 +
S12).
NOTICE
Fig.
e
Screw the tail end (16) with the screw (S11) to
the addendum angle.
4.4.6 Suspending the horizontal rail pairs
Fig.
a
,
pair (14L/14R) at the rear can be carried out in two
assembly versions, depending on the material condi-
tions.
These assembly, operation and maintenance instructions must be kept for the entire period of use!
Do not twist the angle frames (1R)
and (1L)!
When tightening the angle frames,
make sure not to twist or warp them. If
required, shim the angle frames with
suitable material. Hooks to place under-
neath which are suited for this purpose
can be purchased from Novoferm.
b
, page A8. Mount the rail
Potential obstruction at the transition
to the rails.
Make sure there is no offset in the
transition between the guide rails. If ne-
cessary, slightly adjust the arch ends.
page
A9.Suspending
the
rail
Werbung
Inhaltsverzeichnis
