Recommended Usage Of The Programs; Heating Water - Gastroback Design Tee Automat Advanced Plus Bedienungsanleitung

time is counted down (see: 'Keep Warm Function'). You can select the tempe-
rature unit (°C or °F) via the setting mode (see: 'Special Settings').
• The lowest line shows the currently selected program.
• When starting a program, the heating elements start heating. On the "BREW
TEMP" area, a rising bar is shown and the actual water temperature is given in
steps of 5°C. While a program is running, you can display the set values via
pressing the TEMP/TIME button. The set values flash on the display for approx.
5 seconds. Thereafter the display switches back to the actual values. This holds
for the auto start function and the keep warm function as well. As soon as the
set temperature is reached, an acoustic signal sounds and the appliance auto-
matically lowers the tea infuser into the water, while switching to the steeping
time that is shown on the "BREW TIME" area as a count-down.
• During steeping, the temperature within the kettle is kept constant. The automatic
steeping function can immerse and pull out the tea infuser several times for ensu-
ring an optimum extraction (see: 'Automatic Extraction'). After steeping, another
acoustic signal sounds, and the cantilever moves the tea infuser up and out of the
water automatically. On the display, "BASKET" illuminates. You should remove
the kettle from the power base, take out the filter system and close the kettle with
the lid. After 5 minutes, "BASKET" is deleted from the display.
CAUTION
– Do not attempt to remove or replace the kettle, while the can-
tilever is moving. Wait, until the keep warm indicator is illuminated or "BASKET"
is shown on the display.
• With the keep warm function activated, the keep warm function starts immedi-
ately after steeping and the keep warm indicator illuminates (see: 'Keep Warm
Function').
• If you wish to keep your tea warm, simply place the kettle back onto the power
base. In this case, the keep warm function keeps running until the pre-set maxi-
mum keep warm time is reached or until the program is cancelled manually.
• On the "BREW TIME" area, the keep warm time is counted down beginning
with the maximum keep warm time (see: 'Preferences'). After the maximum keep
warm time elapsed, the keep warm indicator gets dark again and the appliance
switches off completely.
• When removing the kettle from the power base, any heating process is can-
celled (see: 'Operation / Cancelling Operation'), but the keep warm function
keeps running. When the program is finished (at the end of the keep warm time
or manually), the values of the recently selected tea program or user-defined pro-
gram are shown on the display.
EN
78
• When the appliance is idle (standby mode: no program running, no entries)
the appliance shuts off automatically and the display gets completely dark (see:
'Automatic Shut-Off').
• When an error occurs during operation or via your entries, in the lowest line of
the display an error message is issued ("E1" to "E4", see: 'Solving Problems /
Error Messages').

RECOMMENDED USAGE OF THE PROGRAMS

Each program is operated according to pre-programmed values. For selecting a pre-
defined tea program, use the selection buttons – or +. Via the FAV./CUS. button,
you can toggle to the user-defined programs (1 to 4) and back. Additionally, heat
clear water via the WATER button (with the cantilever staying in the upper position).
NOTE
While a program is running, no entries of new values are possible. For entering
new values, any running program must be cancelled first (see: 'Operation / Can-
celling Operation'). Nevertheless, pressing the TEMP/TIME button displays the
current settings (temperature, steeping time and selected program).

Heating Water

If you wish to heat clear water, you can select the desired temperature first within the
full range of possible temperature values (50°C to 100°C; 122°F to 212°F). The-
refore, this function can be used for manual brewing (immersing and taking out the
ingredients manually). We recommend to use the filter system even for this purpose.
With the filter system, you simply move the pusher manually down and up.
NOTE
Manual operation may be useful for finding out the optimum steeping time, when
testing a new tea blend. In standby mode (display is illuminated, no program run-
ning) with the desired temperature shown on the display, simply press the WATER
button. The kettle starts heating immediately. When the set temperature is reached,
with an acoustic signal, the appliance switches to the keep warm function (see:
'Keep Warm Function').
EN
79