Seat Adjustment; Bonnet; Quick Connectors For Accessory Hook-Up; Installing An Accessory - Stiga Villa 320 HST Gebrauchsanweisung

EN

6 .11 SEAT ADJUSTMENT (11)

The seat can be tilted and moved
backwards and forwards to suit the driver.
The seat can be locked in the tilted up posi-
tion using the locking lever (11:B).
To set the seat in the desired position:
• Slacken the screws (11:A).
• Move the seat to the desired position.
• Tighten the screws (11:A).
Tightening the screws to a torque over
24 Nm, will damaged the seat.
The seat is equipped with a safety switch
that is connected to the machine's safet y
system. This means that when the driver is
not sitting in the driver's seat or he gets up
from it, it becomes impossible to activate the
commands or carry out any actions which
could compromise the safety of the driver
(see 7.5.2).

6 .12 BONNET

Open the bonnet to fill up with fuel and
check/top up/change the engine oil .
The bonnet is opened by simply lifting it from the
front edge.
The machine must never be activated
when the bonnet is open. Burns hazard.
6 .13 QUICK CONNECTORS FOR ACCESSO-
RY HOOK-UP (12:A)
The quick connectors for accessory hook-up
make it possible to:
• swap over accessories quickly and easily.
• quickly and easily move the accessory
between two positions, i.e.;
• Operating position, accessory engaged
with the drive belt taut.
• Retracted position (4 cm behind the ope-
rating position) with the accessory disen-
gaged and the drive belt slack.
Being as the belt tensioner (13:A) is freed of the
belt, the accessories quick connectors simplify the
swapping over from one accessory to another and
belt replacement.
6 .13 .1

Installing an accessory

If the accessory is a cutting-means assembly:
14
ENGLISH
1 . Adjust the minimum cutting height.
2 . Place the hooks of the cutting-means assem-
bly (12:A) on the pins on the handles (12:B).
3 . Wind the belt around the pulley (13:A) on the
machine.
The cutting-means assembly must ne-
ver be activated if the belt guard is not
in place. Risk of crushing injuries. .
4 . Turn the handles (12:B) (approx. 180°)
upwards until the fastener (12:C) locks into
the hook groove (12:A).
5 . Tension the belt by applying the tensioners
(13:B) on the internal part of the belt.
6 . Install the belt guard (14:A) and lock in place
with a 17-mm wrench to tighten the bolt
(14:B). Make sure the belt guard is in the
correct position.
7 . If the accessory is a cutting deck with electric
height regulation: connect the electric cable
to the socket on the front right of the machine
(9:G).
8 . Hook the deck up to the accessory lifting
device (8:E).
6 .13 .2
If the accessory is a cutting-means assembly
1 . Adjust the minimum cutting height.
2 . Remove the belt guard (14:A) using a 17-mm
wrench.
The cutting-means assembly must ne-
ver be activated if the belt guard is not
in place. Risk of crushing injuries. .
If the accessory is a cutting-means assembly with
electric height regulation::
1 . Disconnect the cable from the machine (9:G).
2 . Slacken the belt tension by removing the ten-
sioners (13:B) from the belt.
3 . Release the fastener (15:A) on both sides, lift
up and turn the handles (15:B) downwards.
4 . Remove the belt from the machine pulley.
5 . Lift the accessory's hooks (15:C) from the
installation points..

7 START-UP AND OPERATION

7 .1

PRECAUTIONS FOR USE

Always make sure the engine oil level
is correct . This is particularly important
when operating on slopes (see 7.4).
Be very careful when cutting grass on
(Translation of the Original Instructions)

Removing an accessory