Safety Instructions; Symbols And Icons; Graphical Symbol Additionally On The Saw Blades; Symbols In The Manual - Parkside PTKS 2000 G5 Originalbetriebsanleitung

GB IE
Height adjustment ................................................... 0 - 85 mm
Saw blade, swivelling .................................................90 - 45°
Extraction connection .................................................ø 34 mm
Weight ..................................................................... 21,5 kg
Laser class ...........................................................................2
Laser wavelength ....................................................... 650 nm
Laser power ............................................................. < 1 mW
Laser module power supply .................... 2 x 1.5 V Micro (AAA)
Sound pressure level (L ) .......................93.7 dB(A); K
pA
Sound power level (L )
WA
measured ....................................... 106.7 dB(A); K
guaranteed .........................................................108 dB(A)
* Operating mode S6 40%: Continuous operation with intermittent load
(cycle time 10 min). In order not to heat the motor more than permitted,
the motor may only be operated for 40% of the cycle time with the stated
nominal power and must then continue running for 60% of the cycle time
without a load.
**Operating mode S1: Continuous operation with constant load
This appliance is intended to be operated using a mains supply
network with a system impedance (internal resistance of the
mains) Zmax on the transfer point (house connection) of maximum
0.5367 Ohm. The user must ensure that the appliance is only op-
erated using a mains supply network meeting the requirements. If
necessary, local power supply companies can be consulted with
regards to the system impedance.
- The specified total vibration value and the stated noise emis-
sion value have been measured according to a standardised
test method and can be used to compare one power tool with
another.
- The specified total vibration value and the stated specified
noise emission value can also be used for a provisional as-
sessment of the load.
Warning:
The vibration and noise emissions may deviate from the
specified values during actual use of the power tool,
depending on how the power tool is being used and, in
particular, what kind of material is being worked on.
Safety measures for the protection of the operator are to
be determined that are based on an estimate of the actual
vibration load under the real operating conditions (for
this, all parts of the operating cycle are to be taken into
account, for example, times in which the electric tool is
turned off, and those during which it is turned on but run-
ning without a load).

Safety instructions

CAUTION! The following basic safety precautions must be ob-
served while using electric tools to protect against electric shock,
injury and risk of fire. Please read all instructions before using this
electric tool and keep the safety instructions in a safe place.

Symbols and icons

Symbols on the appliance:
Carefully read these Operating Instructions.
Wear eye protection.
Wear ear protection.
Wear breathing protection.
22
Caution - Risk of injury.
Never reach into the running blade.
Do not expose the unit to rain. The device must not be
wet, nor should it be operated in a moist environment.
Caution! - Laser radiation. Do not look into the beam.
Laser class 2
= 3 dB
pA
= 3 dB
WA
This label is attached to the saw blade guard.
Safety class II (Double Isolated)
Electrical appliances must not be disposed of with the
domestic waste.
Speed 3200 min
Speed 5000 min

Graphical symbol additionally on the saw blades

Caution - a damaged blade must not be used under any
circumstances. Replace the saw blade immediately.

Symbols in the manual

Warning symbols with information on damage
and injury prevention.
Instruction symbols (the instruction is explained at the
place of the exclamation mark) with information on pre-
venting damage.
Help symbols with information on improving tool
handling.
Hazard symbol with information on the prevention of per-
sonal injury caused by electric shock.
Warning! Electric shock hazard.
Always unplug the device before working on it.

General safety instructions for power tools

WARNING! Read all safety directions and in-
structions. Omissions in the compliance with safety
directions and instructions can cause electrical shock, fire
and/or severe injuries.
Retain all safety directions and instructions for future
use. The term "Power Tools" used in the safety instructions refers
to mains-operated power tools (with power cord) and to bat-
tery-operated power tools (without power cord).
-1
-1