Inhaltsverzeichnis
Werbung
PRODUCT PARTS
(a) User guide storage compartment
(b) Backrest
(c) Adjustable headrest
(d) Headrest height adjuster
(e) Booster
(f)
Impact shield
(g) Belt guide - Group 1
(h) Lap belt guide - Group 2/3
(i)
Shoulder belt guide
(j)
Linear Side-impact Protection
(L.S.P)
(k) ISOFIX-Connect-locking arms
THE CORRECT POSITION IN THE VEHICLE
The car seat with retracted ISOFIX-Connect-locking arms (k) can be used on
all vehicle seats with automatic three-point safety belts approved in the vehicle
manual for "universal" use.
A "semi-universal" certification is given to restraint systems that are connected
to the vehicle through ISOFIX-Connect-locking arms (k). For this reason,
ISOFIX-Connect can only be used in certain vehicles. Refer to the enclosed
vehicle type list for approved vehicles. You can obtain the most up-to-date
version from www.cybex-online.com.
In exceptional cases, the car seat may also be used on the front passenger
seat. Always comply with the recommendations of the vehicle manufacturer.
INSTALLING THE CAR SEAT IN THE VEHICLE
1. Always ensure that...
• the backrests in the vehicle are locked in their upright position.
• when installing the car seat on the front passenger seat, adjust the vehicle
seat as far back as possible without affecting the belt routing.
2. Use the ISOFIX-Connect-adjustment handle (l) under the booster (e) and
pull the two ISOFIX-Connect-locking arms (k) to their furthest extent.
3. Now twist the ISOFIX-Connect-locking arms (k) 180° so that they are facing
the direction of the ISOFIX-anchorage points (o).
4. Place the car seat on the appropriate seat in the vehicle.
(l)
ISOFIX-Connect-adjustment
handle
(m) ISOFIX-Connect-release button
(n) ISOFIX-Connect-safety indicator
(o) ISOFIX-anchorage points
(p) L.S.P.-operating button
(q) Central adjustment button of the
impact shield
(r)
Position adjustment button
(s) Base
(t)
Release buttons of the base
(u) Snap dips
(v) Lever for reclining headrest
5. Push the two locking arms (k) into the ISOFIX-anchorage points (o) until
these lock into place with an audible "CLICK".
6. Use the ISOFIX-Connect-adjustment handle (l) and push the car seat
against the vehicle seat.
7. Ensure that the entire surface of the backrest of the car seat (b) is placed
against the backrest of the vehicle seat.
If the headrest of the vehicle is in the way, pull it upwards to its furthest
��
extent or remove it completely (except in rear-facing vehicle seats).
8. Ensure the car seat is secure by trying to pull it out of the ISOFIX-anchorage
points (o). The green safety indicators (n) must be clearly visible on both
sides of the car seat.
9. In case the car seat is used without ISOFIX-Connect, it can be stored away
on the bottom of the car seat.
10. To activate the Linear Side-impact Protection (L.S.P.) (j) press the L.S.P.-
operating button (p).
By using ISOFIX-Connect, a connection to the vehicle is created which
��
increases your child's safety. Your child still needs to be secured with the
three-point belt of the vehicle and the impact shield for Group 1.
The car seat can also be used with the Linear Side-impact Protection
��
(L.S.P.) folded in if there is not enough space in the vehicle or if the Linear
Side-impact Protection (L.S.P.) is in conflict with the vehicle door.
REMOVING THE CAR SEAT FROM THE VEHICLE
Perform the installation steps in the reverse order.
1. Unlock the ISOFIX-Connect-locking arms (k) on both sides by pushing
the release buttons (m) and pulling them back simultaneously.
2. Pull the car seat away from the ISOFIX-anchorage points (o).
3. Remove the car seat and store the ISOFIX-Connect in reverse order
to installation.
ADJUSTING THE HEADREST
The headrest (c) can be adjusted by using the headrest height adjuster (d)
at the back of the headrest (c). Adjust the headrest (c) so that max. 2 cm
(approx. 2 finger's width) remain between the child's shoulder and the headrest
(c).
The height of the headrest can still be adjusted while the car seat is
��
installed in the vehicle.
EN
7
Werbung
Inhaltsverzeichnis
