Residual Risks; Technical Data - Parkside PMTS 210 A1 Originalbetriebsanleitung

Safety instructions for the handling of saw blades
1. Only use insertion tools if you have mastered their use.
2. Observe the maximum speed. The maximum speed spec-
ified on the insertion tool may not be exceeded. If speci-
fied, observe the speed range.
3. Observe the motor / saw blade direction of rotation.
4. Do not use any insertion tools with cracks. Sort out
cracked insertion tools. Repairs are not permitted.
5. Clean dirt, grease, oil and water off of the clamping sur-
faces.
6. Do not use any loose reducing rings or bushes to reduce
holes on circular saw blades.
7. Make sure that fixed reducer rings for securing the inser-
tion tool have the same diameter and have at least 1/3
of the cutting diameter.
8. Make sure that fixed reducer rings are parallel to each
other.
9. Handle insertion tool with caution. They are ideally
stored in the originally package or special containers.
Wear protective gloves in order to improve grip and to
further reduce the risk of injury.
10. Prior to the use of insertion tools, make sure that all pro-
tective devices are properly fastened.
11. Prior to use, make sure that the insertion tool meets the
technical requirements of this electric tool and is properly
fastened.
12. Only use the supplied saw blade for cutting wood, never
for the processing of metals.
13. Use the correct saw blade for the material to be pro-
cessed.
14. Use only a saw blade with a diameter that matches the
specifications on the saw.
15. Use only saw blades that are marked with an equal or
higher rotational speed than that marked on the electric
tool.
16. Use only saw blades recommended by the manufacturer
which conform to EN 847-1, if intended for cutting wood
or similar materials.
17. Wear suitable personal protective equipment, such as:
- hearing protection;
- protective gloves when handling saw blades.
18. Only use saw blades recommended by the manufacturer
which conform to EN 847-1. Warning! When changing
the saw blade, ensure that the cutting width is not smaller
and the width of the saw blade disc is not greater than
the thickness of the riving knife!
19. When sawing wood and plastics, avoid the saw teeth
overheating. Reduce the feed speed in order to avoid the
plastic melting.

Residual risks

This power tool has been constructed in accord-
ance with the latest technology and the generally
recognised safety regulations. However, individu-
al residual risks can arise during operation.
• Health hazard due to electrical power, with the use of im-
proper electrical connection cables.
• Furthermore, despite all precautions having been met, some
non-obvious residual risks may still remain.
56 GB/MT
• Residual risks can be minimised if the "safety instructions"
and the "Proper use" are observed along with the whole of
the operating instructions.
• Do not put any unnecessary stresses on the machine: exces-
sive pressure during sawing will quickly damage the saw
blade. This may result in a reduction in the performance of
the machine, as well as a reduction in the cutting accuracy.
• Avoid accidental starting of the machine: the operating but-
ton may not be pressed when inserting the plug in an outlet.
• Use the tool that is recommended in this manual. This will
ensure the optimal performance of your saw.
• Keep your hands away from the working area when the ma-
chine is in operation.
• Before you carry out any adjustments or servicing work, turn
the device off and remove the mains plug.

7. Technical data

AC motor......................................................220-240 V~ 50 Hz
Power consumption .........................................1200 Watt (S1*)
Idle speed n ............................................................... 4800 rpm
0
Hard metal saw blade ..........................ø 210 x ø 30 x 2.6 mm
Number of teeth .......................................................................24
Riving knife thickness ........................................................2,0 mm
Min. size of workpiece W x L x H .................. 10 x 50 x 1 mm
Table size .............................................................485 x 445 mm
Table width extension .........................................485 x 515 mm
Table size max. ....................................................485 x 630 mm
Cutting height max. 45° ...................................................45 mm
Cutting height max. 0° .....................................................48 mm
Tilting saw blade ......................................................... 0-45° left
Suction connection ........................................................ ø 35 mm
Weight .................................................................. approx. 14 kg
Machine size (with extension)
W x L x H ................................................. 485 x 630 x 440 mm
*S1: Continuous operation at constant load
**S6 25%:
Continuous duty with intermittent loading (operating time 10
min.)
In order avoid impermissible overheating of the motor, the mo-
tor should be driven for only 25% of the operating time with the
stipulated nominal power and must then continue to run with no
load for the remaining 75% of the operating time.
Noise
The total noise values were determined in accordance with
EN 62841.
Sound pressure level L ............................................ 87,5 dB(A)
pA
Uncertainty K ......................................................................3 dB
pA
Sound power level L ............................................100,5 dB(A)
WA
Uncertainty K .....................................................................3 dB
WA
Wear hearing protection.
Excessive noise can result in a loss of hearing. Total vibration
values (vector sum - three directions) determined in accordance
with EN 62841.
1500 Watt (S6 25%**)