Operation - Parkside PMTS 210 A1 Originalbetriebsanleitung

9.4 Removing/fitting the table inlay (fig. 8)
m WARNING:
In the event of wear or damage the table inlay (6) must be
replaced; otherwise there is an increased danger of injury.
1. Move the saw blade into the bottom position (see 10.2)
2. Take off the saw blade guard (4).
3. Remove the table inlay screws (32).
4. Remove the table inlay (6).
5. Installation of the table inlay (6) takes place in reverse
order.
9.5 Setting the riving knife (fig. 9)
m WARNING:
Pull out the mains plug.
m WARNING:
The setting of the saw blade (5) must be checked after every
saw blade replacement.
1. Set the saw blade (5) to the max. cutting depth, move to
the 0° position and lock in place (see 10.2).
2. Remove the saw blade guard (4) (see 9.3).
3. Remove the table inlay (6) (see 9.4).
4. Loosen the fastening screws (33)
5. Align the riving knife (3) such that
a) the distance between the saw blade (5) and the split-
ter (3) is max. 5 mm (fig. 10) and
b) the saw blade (5) is parallel to the splitter (3).
6. Retighten the fastening screws (33) and fit the table insert
(6) (see 9.4).
7. Fit the saw blade guard (4) again (see 9.3).
9.6 Fitting/replacing the saw blade (fig. 11, 12)
m WARNING:
Pull out the mains plug and wear protective gloves.
1. Remove the saw blade guard (4) (see 9.3).
2. Unscrew the screws (34) on the bottom saw blade cover
(35) and open it out.
3. Loosen the nut by applying the 19 mm ring spanner (21)
to the nut and holding the motor shaft in place with an
8 mm ring spanner (20) (Fig. 12).
ATTENTION:
Turn the nut in the direction of rotation of the saw blade.
4. Take off the outer flange and pull the old saw blade
down and off the inner flange at an angle.
5. Clean the saw blade flange carefully with a wire brush
before installing the new saw blade.
6. Insert the new saw blade in the reverse sequence and
tighten.
m WARNING:
Pay attention to the running direction. The cutting angle of
the teeth must point in the running direction, i.e. forwards
(see arrow on the saw blade guard (4)).
7. Close the bottom saw blade cover (35) and tighten the
screws (34) again.
8. Refit the saw blade guard (4) and adjust it (see 9.3).
m WARNING:
Check the protective devices before working with the saw
again.
58 GB/MT
9.7 Fitting the parallel stop (7) (fig. 2, 15)
1. Fasten the holder (16) to the table with the help of the
locking knobs (15) and the clamping plates (15a).
2. Make sure that the holder (16) is aligned parallel to the
saw blade (5). If necessary, readjust it with the aid of the
scale (38).
3. Slide the sliding block along the groove (37) in the stop
rail (17).
4. Fasten the stop rail (17) to the holder (16) with the help
of the screws (16a).
9.8 Fitting the transverse stop (fig. 18)
1. Slide the transverse stop (2) in the groove (40) of the
saw table (1).
2. Loosen the turning handle (19).
3. Turn the transverse stop (2) until the arrow points to the
desired angle.
4. Retighten the turning handle (19).
9.9 Chip extraction (fig. 13)
ATTENTION:
Only operate the device with an extraction system.
Connect a suitable chip extraction system (not included in the
scope of delivery) to the suction port (36).
ATTENTION:
Check and clean the suction channels at regular intervals.
9.10 Stable fastening (fig. 25)
The machine must be securely installed, i.e. bolted down on a
workbench, machine stand or similar, as shown in fig. 25.
Use the bracket for workbench mounting (42), the screws (43)
and the washers (44) to do so.

10. Operation

10.1 Switches (fig. 1)
10.1.1 On/off switch (11)
• It is possible to switch the saw on by pressing the green "I"
button. Before starting sawing, wait until the saw blade has
reached its maximum speed.
• In order to switch the saw off again, it is necessary to press
the red "0" button.
10.1.2 Overload switch (10)
The device motor is protected against overload with an over-
load switch (10).
In the event of the nominal current being exceeded, the over-
load switch (10) switches the device off.
If this happens, proceed as follows:
• Let the device cool down for several minutes.
• Press the overload switch (10).
• Switch the device on by pressing the green "I" button.
10.2 Setting the cutting depth (Abb. 1)
The saw blade (5) can be adjusted to the required cutting
depth by turning the hand wheel (8).
• Counterclockwise: Greater cutting depth