Residual Risks; Technical Data - Parkside PMTS 210 A1 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

14. Use only a saw blade with a diameter that matches the
specifications on the saw.
15. Use only saw blades that are marked with an equal or
higher rotational speed than that marked on the power
tool.
16. Use only saw blades recommended by the manufacturer
which conform to EN 847-1, if intended for cutting wood
or similar materials.
17. Wear suitable personal protective equipment, such as:
– hearing protection;
– protective gloves when handling saw blades.
18. Use only saw blades recommended by the manufacturer
which conform to EN 847-1. Warning! When changing
the saw blade, make sure that the cutting width is not small-
er and the thickness of the saw blade is not greater than
the thickness of the splitter.
19. When sawing wood and plastics, avoid overheating the
saw teeth. Reduce the feed speed to avoid the plastic melt-
ing.

Residual Risks

This power tool has been constructed in accord-
ance with the latest technology and the generally
recognised safety regulations. Nevertheless, it is
possible that individual residual risks may occur
during operation.
• Electrical hazard if improper electrical connection cables are
used.
• In addition, concealed residual risks may be present in spite
of all the precautions that have been taken.
• Residual risks can be minimised by observing the „Safety
instructions" and „Use in accordance with the designated
purpose", as well as the operating instructions.
• Do not put any unnecessary stresses on the machine: exces-
sive pressure during sawing will quickly damage the saw
blade. This may result in a reduction in the performance of
the machine, as well as a reduction in the cutting accuracy.
• Avoid switching the machine on by accident: when insert-
ing the plug into the socket, the power button must not be
pressed.
• Use the tool which is recommended in this manual. This will
ensure the optimal performance of your saw.
• Keep your hands away from the working area when the ma-
chine is in operation.
• Before you carry out any adjustments or servicing work, turn
the device off and remove the mains plug.
24 GB

6. Technical data

AC motor......................................................220-240 V ~ 50 Hz
Power consumption .........................................1200 Watt (S1*)
................................................................... 1500 Watt (S6 25%)
Idle speed n .............................................................. 4800 min
0
Hard metal saw blade ..........................ø 210 x ø 30 x 2,6 mm
Number of teeth .......................................................................24
Riving knife thickness ........................................................2.0 mm
Min. size of workpiece W x L x H .................. 10 x 50 x 1 mm
Table size .............................................................485 x 445 mm
Table width extension .........................................485 x 515 mm
Table size max. . ..................................................485 x 630 mm
Cutting height max. 45° ...................................................45 mm
Cutting height max. 90° ...................................................48 mm
Tilting saw blade ......................................................... 0-45° left
Suction connection ........................................................ ø 35 mm
Weight .................................................................. approx. 14 kg
Machine size (with extension)
W x L x H ................................................. 485 x 630 x 440 mm
*S1: Continuous operation at constant load
**S6 25% operating mode:
Continuous duty with intermittent loading (operating time 10
min.)
In order avoid impermissible overheating of the motor, the mo-
tor should be driven for only 25% of the operating time with the
stipulated nominal power and must then continue to run with no
load for the remaining 75% of the operating time.
Noise
The total noise values were determined in accordance with
EN 62841.
Sound pressure level L ............................................ 87.5 dB(A)
pA
Uncertainty K ......................................................................3 dB
pA
Sound power level L ............................................100.5 dB(A)
WA
Uncertainty K .....................................................................3 dB
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total vibration
values (vector sum - three directions) determined in accordance
with EN 62841.
NOTE: The specified device emissions values have been meas-
ured in accordance with a standardised test procedure and
can be used for comparison of one electric tool with another.
The specified device emissions values can also be used for an
initial estimation of the load.
WARNING: The noise emission values can vary from the
specified values during the actual use of the electric tool, de-
pending on the type and the manner in which the electric tool is
used, and in particular the type of workpiece being processed.
Implement measures to protect against noise nuisance. In do-
ing so, take into account the complete working process, includ-
ing the times when the electric tool is working without load or
switched off.
Suitable measures include regular maintenance and care of the
electric tool and the insertion tools, regular breaks as well as
proper planning of the working process.
-1