Safety Instructions For Handling The Laser; Safety Instructions For Handling Batteries; Residual Risks; Electrical Connection - Parkside PTK 2000 C3 Originalbetriebsanleitung

GB MT
c) Extending a spanner or tightening with the help of hammer
blows is not permitted.
d) The tightening surfaces must be cleaned to remove any dirt,
grease, oil and water.
e) Tensioning bolts must be tightened in accordance with the
manufacturer's instructions.
f) In order to adjust the borehole diameter of circular saw
inserted rings, e.g. rings which have been pressed into place
or which are held in place by means of an adhesive bond,
may be used. The use of loose rings is not permitted.
one another.

Safety Instructions for Handling the Laser

– Caution: Laser radiation - Do not look into the beam - Laser
class 2

Safety Instructions for Handling Batteries

1 Ensure at all times that the batteries are inserted with the
correct polarity (+ and –), as shown on the battery itself.
2 Do not short-circuit the batteries.
3 Do not charge up rechargeable batteries.
4 Do not overcharge the battery!
5 Do not mix old and new batteries or batteries of a different
type or from different manufacturers! Replace all batteries of
a set at the same time.
6 Remove used batteries immediately out of the device and
dispose of them correctly!
7 Do not heat the batteries!
8 Do not carry out any welding or soldering work directly to
the batteries!
9 Do not take the batteries apart!
10 Do not deform the batteries!
11
12 Store the batteries out of the reach of children.
13 Do not allow children to replace the batteries without supervi-
sion!
14
sources of heat. Do not place the battery in direct sunlight
and do not use or store it in motor vehicles in hot weather.
15 Store used batteries in the original packaging and keep them
away from metal objects. Do not mix (up) unpacked batte-
ries! Otherwise this may cause the battery to short-circuit,
16 Remove batteries from the device if this is not going to be
used for a prolonged period, unless it is to be used in emer-
gencies!
17 NEVER touch batteries which have leaked without appro-
priate protection. If the leaked liquid comes into contact with
the skin, you should rinse off this area of the skin immedia-
tely under running water. Make sure at all events that your
eyes and mouth do not come into contact with the liquid. If
they do, seek medical advice immediately.
18 Clean the battery contacts and the equivalent contacts in the
device before inserting the batteries.
38

Residual Risks

This power tool has been constructed in accordance
with the latest technology and the generally recog-
nised safety regulations. Nevertheless, it is possible
that individual residual risks may occur during opera-
tion.
• Electrical hazard if improper electrical connection cables are
used.
• In addition, concealed residual risks may be present in spite
of all the precautions that have been taken.
• Residual risks can be minimised by observing the „Safety
instructions" and „Use in accordance with the designated
purpose", as well as the operating instructions.
• Do not put any unnecessary stresses on the machine: exces-
sive pressure during sawing will quickly damage the saw
blade. This may result in a reduction in the performance of
the machine, as well as a reduction in the cutting accuracy.
• Avoid switching the machine on by accident: when inserting
the plug into the socket, the power button must not be pressed.
• Use the tool which is recommended in this manual. This will
ensure the optimal performance of your saw.
• Keep your hands away from the working area when the
machine is in operation.
• Before you carry out any adjustments or servicing work, turn
the device off and remove the mains plug.

Electrical Connection

The installed electric motor is connected ready for
operation. The connection complies with the relevant
VDE and DIN regulations. The customer's network
connection and any extension cable used must com-
ply with these regulations.
• The product meets the requirements of EN 61000-3-11 and
is subject to special connection conditions. This means that
its use at freely selectable connection points is not permitted.
• If the network conditions are unfavourable, the device may
• The maximum permitted mains impedance at the electrical
connection point of 0.107 ohm must not be exceeded.
• As the user, you must ensure – in consultation with your
electricity supply company if necessary – that the continuous
current carrying capacity of the network at the connection
the product.

Important Instructions

If the motor is overloaded, it switches itself off automatically.
After cooling down (times vary), the motor can be switched on
again.

Faulty Electrical Connection Cable

Insulation damage often occurs to electrical connection cables.
The causes of this may be as follows:
• Pressure points if connection cables are routed through
windows or door gaps.