General Notes; Cylindrical Sanding Machine - Scheppach csm 405 Original Anleitungen

Manufacturer:
Scheppach
Fabrikation von Holzbearbeitungsmaschinen
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
we wish you a pleasant and successful working experience
with your new machine.
Note:
According to the applicable product liability law the man-
ufacturer of this device is not liable for damages which
arise on or in connection with this device in case of:
• improper handling
• non-compliance with the instructions for use
• repairs by third party, non authorized skilled workers
• installation and replacement of non-original spare parts
• improper use
• failures of the electrical system due to the non-
compliance with the electrical specifications and the
VDE 0100, DIN 57113 / VDE 0113 regulations
Recommendations:
Read the entire text of the operating instructions prior to
the assembly and operation of the device.
These operating instructions are intended to make it eas-
ier for you to get familiar with your device and utilize its
intended possibilities of use.
The operating instructions contain important notes how to
work safely, properly and economically with your machine
and how to avoid dangers, save repair costs, reduce down-
time, and increase the reliability and working life of the
machine.
In addition to the safety regulations contained herein, you
must in any case comply with the applicable regulations of
your country with respect to the operation of the machine.
Put the operating instructions in a clear plastic folder to
protect them from dirt and humidity, and store them near
the machine. The instructions must be read and carefully
observed by each operator prior to starting the work. Only
persons who have been trained in the use of the machine
and have been informed on the related dangers and risks
are allowed to use the machine. The required minimum
age must be met.

General Notes

• When you unpack the device, check all parts for pos-
sible transport damages. In case of complaints the
supplier is to be informed immediately. Complaints
received at a later date will not be acknowledged.
• Check the delivery for completeness.
• Read the operating instructions to make yourself famil-
iar with the device prior to using it.
• Use only original parts for accessories as well as for
wearing and spare parts. Spare parts are available from
your specialized scheppach dealer.
• Specify our part numbers as well as the type and year
of construction of the device in your orders.
12 english
csm 405
Scope of delivery

Cylindrical Sanding Machine

Handle for Height Adjustment
Crank for Height Adjustment
Bow - Suction Connection
Specifications
Dimensions
L x W x H mm
Height of sanding min. /
max. mm
Width of sanding max. mm
Table height with stand
mm
Sanding belt length/
width mm
Sanding surface with
table mm
Sanding belt coarseness
Belt speed m/sec
ø Suction nozzles mm
Weight kg
Drive
Motor V/Hz
Input P1 kW
Output P2 kW
Rotational speed rpm
Undervoltage release
Plug
Operating mode
Subject to technical modifications!
Noise parameters according to EN 23746
The noise emission values determined according to
EN 23746 for the sound power level or according to
EN 31202 (correction factor k3 calculated according to
Annex A.2 of EN 31204) for the sound level at the work
place are based on the working conditions specified in
ISO 7960 Annex A and are as follows:
Sound power level at the work place in dB
Idle running L = 77.0 dB(A)
WA
Processing L = 87.0 dB(A)
WA
Sound level at the work place in dB
Idle running L = 69.0 dB(A)
pAeq
Processing L = 77.0 dB(A)
pAeq
A measuring incertainty allowance K=4 dB applies for the
specified emission values.
Specifications regarding the dust emission
The dust emission values that were measured according
to the "Principles for the evaluation of the dust emission
(concentration parameters) of wood working machines" of
the Fachausschuss Holz (Expert committee wood) are be-
low 2 mg/m . Thus, it can be assumed that the TRK limit
3
value for wood dust applicable in the Federal Republic of
Germany is permanently and reliably fallen short of when
the machine is connected to a proper operational suction
plant with an air speed of at least 20 m/s.
Please observe the load values of the material manufac-
turer depending on the materials to be processed or the
material quality.
Adapter Table
Base
2 Extension Tables
Operating Instructions
1005 x 850 x 670
2,5/130
405
720
2400/77
420
80 / 120 / 240
9,68
100
83,0
230–240V/50 Hz
2,00
1,50
1400
yes
Netzstecker
S6 40%