General Notes; Safety Instructions - Scheppach nsm 200 Originalanleitung

Manufacturer:
Scheppach Fabrikation von Holzbearbeitungsmaschinen GmbH
GÜnzburger Straße 69
D-89335 Ichenhausen / BRD
Dear customer,
we wish you a pleasant and successful working experience
with your new scheppach circular wet grinding machine.
According to the applicable product liability law the
manufacturer of this device is not liable for damages which
arise on or in connection with this device in case of:
• improper handling
• non­compliance with the instructions for use
• repairs by third party, non authorized skilled workers
• installation and replacement of non­original spare parts
• improper use
• failures of the electrical system due to the non­
compliance with the electrical specifications and the
VDE 0100, DIN 57113 / VDE 0113 regulations
Recommendations:
Read the entire text of the operating instructions prior to the
assembly and operation of the device.
These operating instructions are intended to make it easier
for you to get familiar with your device and utilize its in-
tend ed possibilities of use.
The operating instructions contain important notes on
how to work safely, properly and economically with your
machine and how to avoid dangers, save repair costs,
reduce downtime, and increase the reliability and working
life of the machine.
In addition to the safety regulations contained herein, you
must in any case comply with the applicable regulations of
your country with respect to the operation of the machine.
Put the operating instructions in a clear plastic folder to
protect them from dirt and humidity, and store them near
the machine. The instructions must be read and carefully
observed by each operator prior to starting the work. Only
persons who have been trained in the use of the machine
and have been informed on the related dangers and risks
are allowed to use the machine. The required minimum
age must be met.
In addition to the safety notes contained in the present
operating instructions and the special regulations of your
country, the generally recognized technical rules for the
operation of wood working machines must be observed.

General Notes

• When you unpack the device, check all parts for possible
transport damages. In case of complaints the supplier is
to be informed immediately.
• Complaints received at a later date will not be
acknowledged.
• Check the delivery for completeness.
• Read the operating instructions to make yourself familiar
with the device prior to using it.
• Use only original parts for accessories as well as for
wearing and spare parts. Spare parts are available from
your specialized dealer.
• Specify our part numbers as well as the type and year of
construction of the device in your orders.
All manuals and user guides at all-guidesbox.com
Scope of delivery
Specifications
Dimensions
LxWxH mm
Tool rest
ø mm
Grinding
stone ø mm
Idle-running
speed
- grinding
stone 1/min.
Cutting
speed m/sec.
Weight kg
Drive
Motor V
Input P1 kW
Output P2
kW
Motor speed
1/min.
Operating
mode
Current
rating A
Subject to technical modifications!!
Information relating to your safety are highlighted with this
symbol in the present operating instructions.
Operators' Training
• Pass the safety instructions to all persons working with
the machine.
• The operator must be at least 18 years old. Trainees
must be at least 16 years old, but are only allowed to
use the machine under supervision.
• Persons operating the machine must not be distracted.
• Keep away children from the machine if it is connected
to the mains.
• Always wear tight clothes. Remove jewelry, rings, and
wrist watches.
• Observe all safety instructions and warnings on the
machine and maintain them in a readable state.
• Be careful when working with the machine: the rotating
grinding tool may cause injuries of fingers and hands.
Stability
• Make sure the machine is installed on a firm ground with
sufficient stability.
• Make sure the workplace is sufficiently illuminated.
Mains Connection of the Machine
• Check the mains connecting lines. Do not use defective
lines. See electrical connection.
• Pay attention to the direction of rotation of the motor
and the tools. See electrical connection.
nsm 200
Grinding stone
jig 60 / 70
Abrasive paste
Angle measurer 200
stone grader
Leather honing disc
Operating instructions
348 x 285 x 270
12
200/12 x 40
120
1,2
12
220 – 240
120
60
1400
S1
0,6
m Safety Instructions
english 7