General Notes - Scheppach 5903304901 Originalanleitung

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
we wish you a pleasant and successful working experi-
ence with your new Kity machine.
According to the applicable product liability law the man-
ufacturer of this device is not liable for damages which
arise on or in connection with this device in case of:
• improper handling,
• non-compliance with the instructions for use,
• repairs by third party, non authorized skilled workers,
• installation and replacement of non-original spare parts,
• improper use,
• failures of the electrical system due to the non-
compliance with the electrical specifications and the
VDE 0100, DIN 57113 / VDE 0113 regulations
Recommendations:
Read the entire text of the operating instructions prior to
the assembly and operation of the device.
These operating instructions are intended to make it eas-
ier for you to get familiar with your device and utilize its
intended possibilities of use.
The operating instructions contain important notes on
how to work safely, properly and economically with your
machine and how to avoid dangers, save repair costs, re-
duce downtime, and increase the reliability and working
life of the machine.
In addition to the safety regulations contained herein, you
must in any case comply with the applicable regulations of
your country with respect to the operation of the machine.
Put the operating instructions in a clear plastic folder to
protect them from dirt and humidity, and store them near
the machine. The instructions must be read and carefully
observed by each operator prior to starting the work. Only
persons who have been trained in the use of the machine
and have been informed on the related dangers and risks
are allowed to use the machine. The required minimum
age must be met.
In addition to the safety notes contained in the present
operating instructions and the special regulations of your
country, the generally recognized technical rules for the
operation of wood working machines must be observed.

General Notes

• When you unpack the device, check all parts for pos-
sible transport damages. In case of complaints the sup-
plier is to be informed immediately. Complaints received
at a later date will not be acknow ledged.
• Check the delivery for completeness.
• Read the operating instructions to make yourself famil-
iar with the device prior to using it.
• Only use original Kity parts for accessories as well as
for wearing and spare parts. Spare parts are available
from your specialized dealer.
• Specify our part numbers as well as the type and year
of construction of the device in your orders.
Bts800
Delivery Status
Belt/Disc Sanding machine
Technical Data
Dimensions
L x W x H mm
ø Disc mm
RPM Disc
Belt
dimensions
mm
Belt Speed m/s
Belt Tilt
Table Size mm
Table Tilt
Gewicht kg
Drive
Motor V~/Hz
Input P1 W
Subject to technical changes!
Noise
Total vibration values determined in accordance with
EN 61029.
sound pressure level L
pA
uncertainty K
pA
sound power level L
WA
uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total
vibration values (vector sum - three directions) deter-
mined in accordance with EN 61029.
FEATURES
SANDING DISC: A round sanding disc located on the
side of the belt/disc sander.
TRACKING KNOB: A tracking knob aids in centering the
sanding belt.
WORK SUPPORT: Supports the workpiece on the sand-
ing belt.
WORKTABLE: Equipped with a sturdy, worktable that
provides a stable surface when using either the disc sand-
ing or the belt sanding feature.
BEVEL GAUGE: The worktable comes equipped with a
bevel gauge that indicates the degrees the worktable can
be tilted up to 45°.
BELT TENSION LEVER: The belt tension lever releases
the belt tension for easy belt replacement.
HORIZONTAL AND VERTICAL POSITION HOLES: The
horizontal and vertical position holes are used for chang-
ing the position of the belt from horizontal to vertical.
SANDING BELT: The sanding belt can be adjusted from
horizontal to vertical providing different positions for sand-
ing workpieces of different shapes and sizes.
Sanding Disc
Disc Guard
Accessory Bag
Operation Manual
475/365/325
150
2850
100 x 915
7,5
0°-90°
215 x 146
0°-45°
21.5
230–240/50
370
85 dB(A)
3 dB
96 dB(A)
3 dB
english 9