Introduction; General Notes; Proper Use - Scheppach 5903203901 Original Bedienungsanleitung

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
we wish you a pleasant and successful working expe-
rience with your new scheppach circular wet grinding
machine.
Note:
According to the applicable product liability law the
manufacturer of this device is not liable for damages
which arise on or in connection with this device in
case of:
• improper handling,
• non-complianceof the operating instructions,
• repairs by third party, non authorized service tech-
nicians,
• installation and replacement of non-original spare
parts,
• application other than specified,
• failures of the electrical system due to the non­
compliance with the electrical specifications and
the VDE 0100, DIN 57113 / VDE 0113 regulations.
Recommendations:
Read the entire text of the operating instructions prior
to the assembly and operation of the device.
These operating instructions are intended to make it
easier for you to get familiar with your device and uti-
lize its in tend ed possibilities of use.
The operating instructions contain important notes on
how to work safely, properly and economically with
your machine and how to avoid dangers, save repair
costs, reduce downtime, and increase the reliability
and working life of the machine.
In addition to the safety regulations contained herein,
you must in any case comply with the applicable reg-
ulations of your country with respect to the operation
of the machine.
Put the operating instructions in a clear plastic folder
to protect them from dirt and humidity, and store them
near the machine. The instructions must be read and
carefully observed by each operator prior to starting
the work. Only persons who have been trained in the
use of the machine and have been informed on the
related dangers and risks are allowed to use the ma-
chine. The required minimum age must be met.
In addition to the safety notes contained in the present
operating instructions and the special regulations of
your country, the generally recognized technical rules
for the operation of wood working machines must be
observed.
We accept no liability for damage or accidents which
arise due to non-observance of these instructions
and the safety information.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

2. General notes

• Open the packaging and carefully remove the
device.
• Remove the packaging material, as well as the
packaging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, keep the packaging until the expiry of
the warranty period.
ATTENTION!
The device and the packaging are not children's
toys! Do not let children play with plastic bags,
films or small parts! There is a danger of choking
or suffocating!

3. Proper use

• The grinding machine has been exclusively de-
signed for grinding steel using the offered tool (no
hard alloy).
• The machine meets the currently valid EU machine
directive.
• The machine has been designed for a one-shift op-
eration, operating factor S1 100%.
• Observe all safety instructions and warnings on the
device.
• Make sure that all safety instructions and warnings
on the machine always are in a readable state.
• Only use the machine if it is in a technically fault-
less state. Pay attention to the intended use, the
safety and dangers and comply with the operating
instructions! Immediately repair (or have repair)
failures which may affect the safety.
• The safety, working, and maintenance instructions
and the dimensions set forth in the specifications
must be observed.
• The applicable regulations for the prevention of
accidents and other, generally recognized safety
rules must be observed.
• The machine may only be used, maintained or re-
paired by trained persons who are familiar with the
machine and have been informed about the dan-
gers. Unauthorized modifications of the machine
exclude a liability of the manufacturer for damages
resulting from the modifications.
• The machine may only be used with original acces-
sories and original tools of the manufacturer.
• Any other use is considered to be not intended.
The manufacturer excludes any liability for result-
ing damages, the risk is exclusively borne by the
user.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial appli-
cations. Our warranty will be voided if the equipment
is used in commercial, trade or industrial businesses
or for equivalent purposes.
GB | 17