Unpacking; Assembly - Parkside PTKS 2000 F4 Bedienungs- Und Sicherheitshinweise

**S6 40 %:
Continuous duty with intermittent loading (operating time 10
min.)
To avoid impermissible overheating of the motor, the motor
should be driven for only 40% of the operating time with the
stipulated nominal power and must then continue to run with no
load for the remaining 60% of the operating time.
Noise
The noise values have been determined in accordance with
EN 62841.
Sound pressure level L ............................................ 96.8 dB(A)
pA
Uncertainty K ......................................................................3 dB
pA
Sound power level L ............................................109.8 dB(A)
WA
Uncertainty K .....................................................................3 dB
WA
m WARNING
Excessive and frequent exposure to noise can lead to hearing
damage or hearing loss.
- Wear hearing protection
- Take breaks.
Total vibration values (vector sum of three directions) deter-
mined according to EN 62841.
NOTE: The specified noise emission values have
been measured in accordance with a standardised
test procedure and can be used to compare one
power tool with another.
The specified noise emission values can also be used for an
initial estimation of the exposure.
WARNING: The noise emission values can vary from the
specified values during the actual use of the power tool, de-
pending on the type and the manner in which the power tool is
used, and in particular the type of workpiece being processed.
Implement measures to protect against noise nuisance.
In doing so, take into account the complete working process,
including the times when the power tool is working without load
or switched off. Suitable measures include regular maintenance
and care of the power tool and the insertion tools, regular
breaks as well as proper planning of the working process.

8. Unpacking

m DANGER
Danger of choking or suffocating
The packaging material, packaging and transport safety de-
vices are not children's toys. Plastic bags, foils and small parts
can be swallowed and lead to choking.
- Keep packaging material, packaging and transport safe-
ty devices away from children.
• Open the packaging and carefully remove the product.
• Remove the packaging material, packaging and transport
safety devices (if applicable).
• Check the completeness of the scope of delivery. The cus-
tomer service must be notified immediately of any com-
plaints. Later claims will not be recognised.
70
GB
• Check the scope of delivery for transport damage. The
transport company must be notified immediately of any com-
plaints. Later claims will not be recognised.
• Keep the packaging until the end of the warranty period.
• Read through the operating manual completely.
• Only use original spare parts or accessories. Original spare
parts or accessories can be obtained from your dealer.
• Check that the data on the type plate matches with the mains
power data.

9. Assembly

m WARNING: Remove the mains plug before maintaining,
modifying or assembling the circular table saw.
m Attention!
Always make sure the device is fully assembled
before commissioning!
You require the following for assembly:
2x open-ended spanner 8/10 mm (k)
1x Allen key 5 mm (l)
(included in the scope of delivery)
1x Phillips screwdriver
1x slotted-head screwdriver
(not included in the scope of delivery)
• Place all supplied parts on a flat surface.
• Group equal parts.
NOTE:
• If connections are secured with a screw (round-head or hexa-
gon), hexagon nuts and washers, the washer must be fitted
under the nut.
• Insert screws each from outside to inside. Secure connections
with nuts on the inside.
• Tighten the nuts and screws during assembly only until they
are unable to fall off. If you tighten the nuts and screws fully
before final assembly, it is not possible to complete the as-
sembly.
9.1 Table width extensions and table extensions
Before assembling the table width extensions and table exten-
sions, you must pre-mount the legs of the base frame.
9.1.1 Pre-mounting the legs of the base frame
(fig. 2)
1. Turn the saw table (2) over and place it on the floor.
2. Fit the four legs (17) into the recesses of the machine hous-
ing.
9.1.2 Fitting table width extensions and table
extensions (fig. 2)
1. The rail joiners (21) are already pre-fitted in the guide rail
(20) of the table width extensions (9).
2. Mount both table width extensions (9) loosely on the saw
table (2) with a total of four hexagon screws M6×12 (a),
four washers M6 (h) and fours nuts M6 (g). To do so, use
the corresponding holes drilled into the saw table (2).