Introduction; Exclusion Of Liability; Device Description (Fig. 1−29) - Parkside PTKS 2000 F4 Bedienungs- Und Sicherheitshinweise

2. Introduction

Dear customer,
We hope your new product brings you much enjoyment and
success.
This operating manual should help you familiarise yourself with
your product and teach you how to use it.
It contains important information on how to work with the prod-
uct safely, properly and economically. This helps you to avoid
danger, costly repairs, reduce downtimes and increase reliabil-
ity and service life of the product.
Please read and observe the operating manual with all instruc-
tions, warnings and information before installation and com-
missioning.
Please note that the figures shown as example figures may devi-
ate from the actual appearance.
In addition to the safety instructions in this operating manual,
you must observe the regulations applicable to the operation of
the product in the country.
Note the following:
The basic steps for using the product are described in this op-
erating manual. It includes all the relevant information about
safety, operation, care and maintenance, disposal and trouble-
shooting for your product.
The operating manual is part of the product and must be kept
close at hand, ready for consultation. Store the operating man-
ual so that it is protected from dirt and moisture. If the product
is handed over to another person, hand over the operating
manual with it.
No claims can be made from the information, figures and de-
scriptions. Possible errors and technical changes in construc-
tion, equipment and accessories in comparison to the informa-
tion and figures in the operating manual are excepted:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Str. 69
D-89335 Ichenhausen

Exclusion of liability

In accordance with the applicable product liability laws, the
manufacturer of this product assumes no liability for damage to
the product or caused by the product arising from:
• Improper handling,
• Non-compliance with the operating manual,
• Repairs carried out by third parties, unauthorised specialists.
• Installing and replacing non-original spare parts,
• Application other than specified.
• Failure of the electrical system in the event of the electrical
regulations and VDE provisions 0100, DIN 13 / VDE0113
not being observed.
We accept no liability for accidents or damage that occur due
to a failure to observe this manual and the safety instructions.
64
GB
3. Device description (fig. 1−29)
1. Parallel stop
1a. Stop rail
1b. Knurled nut
1c. Coach bolt
1d. Phillips screw
2. Saw table
3. Transverse stop
3a. Stop rail
3b. Wing nut
3c. Locking handle
4. Saw blade guard
4a. Wing nut
4b. Coach bolt
5. Riving knife
5a. Fixing screw
5b. Recess on riving knife
6. Saw blade
6a. Open-ended spanner 22 mm
6b. Open-ended spanner 22 mm
6c. Inner saw blade flange
6d. Outer saw blade flange
6e. Drive shaft
6f. Fixing nut
7. Table inlay
7a. Countersunk head screw
8. Table extension
9. Table width extensions
9a. Table width extension left
9b. Table width extension right
10. Speed selection switch
10a. High speed switch
10b. Low speed switch
11. Tilt limiter
12. Scale
13. Locking lever
14. Crank wheel
15. Overload switch
16. On/off switch
17. Leg
18. Rubber foot
19. Tilt protection bar
20. Guide rail (saw table)
21. Rail joiner
22. Table supports
22a. Table support short
22b. Table support medium
22c. Table support long
23. Centre struts
23a. Centre strut short
23b. Centre strut long
24. Laser
24a. Adjustment screw
25. Laser switch
26. Battery compartment
26a. Battery compartment cover
26b. Screw
27. Eccentric lever
28. Scale
29. Guide groove