IFM Electronic CR2052 Programmierhandbuch Seite 252

ifm ProgHB ioControl CR2052 V03.04.00
Index
J1939_RX_FIFO .................................................................................. 160
J1939_RX_MULTI ............................................................................... 162
J1939_SPEC_REQ ............................................................................. 155
J1939_SPEC_REQ_MULTI ................................................................ 157
J1939_STATUS ................................................................................... 153
J1939_TX............................................................................................. 164
J1939_TX_ENH ................................................................................... 165
J1939_TX_ENH_CYCLIC ................................................................... 167
J1939_TX_ENH_MULTI ...................................................................... 169
K
Klemme 15 ........................................................................................... 242
Konfiguration der Ein- und Ausgänge (Voreinstellung) ......................... 52
Konfigurationen ...................................................................................... 43
L
Laufzeitsystem ...............................................................................33, 242
Laufzeitsystem aktualisieren ................................................................. 45
Laufzeitsystem einrichten ...................................................................... 43
Laufzeitsystem installieren .................................................................... 44
LED ...................................................................................................... 242
LED [A]...[D] ........................................................................................... 29
LED [DIA], Diagnose.............................................................................. 29
LED [Lock] ............................................................................................. 29
LED [M], Mode ....................................................................................... 29
LED [PWR], Power ................................................................................ 28
LEDs für Status der Ein- und Ausgänge ............................................... 27
Leistungsgrenzen des Geräts................................................................ 41
Link ...................................................................................................... 242
LSB ...................................................................................................... 242
M
MAC-ID ................................................................................................ 243
Master .................................................................................................. 243
MEM_ERROR ..................................................................................... 206
MEMCPY ............................................................................................. 207
MMI ...................................................................................................... 243
Mögliche Betriebsarten Ein-/Ausgänge ............................................... 230
MRAM .................................................................................................. 243
MSB ..................................................................................................... 243
Multifunktionsanzeige ............................................................................ 28
N
Netzwerkvariablen ................................................................................. 63
NMT ..................................................................................................... 243
Node .................................................................................................... 243
Node Guarding .................................................................................... 243
Notizen • Notes • Notes ....................................................................... 254
O
Obj / Objekt .......................................................................................... 244
Objektverzeichnis ................................................................................ 244
OBV ..................................................................................................... 244
OHC ..................................................................................................... 209
OPC ..................................................................................................... 244
operational ........................................................................................... 244
OUTPUT .............................................................................................. 194
252
P
Parameter der Ausgänge .. 73, 75, 77, 79, 81, 83, 85, 87, 89, 91, 93, 95,
97, 100, 102, 104, 106, 108, 110, 112, 113, 115, 118, 121, 123, 125,
127, 129, 132, 133, 136, 138, 141, 143, 145, 148, 150, 152, 153, 156,
157, 159, 161, 162, 164, 166, 168, 170, 173, 176, 177, 178, 181, 184,
187, 190, 193, 195, 197, 199, 200, 201, 202, 203, 204, 205, 206, 208,
210, 212, 214, 216, 217, 218, 220, 222, 223, 224
Parameter der Eingänge ... 73, 74, 75, 76, 79, 80, 82, 84, 86, 89, 90, 92,
95, 96, 99, 101, 103, 106, 108, 109, 112, 113, 114, 117, 120, 122, 124,
127, 128, 131, 133, 135, 137, 140, 142, 144, 147, 150, 152, 153, 155,
157, 159, 160, 162, 164, 165, 167, 169, 172, 175, 177, 178, 180, 186,
189, 193, 194, 196, 199, 200, 201, 202, 203, 204, 205, 206, 207, 209,
211, 213, 215, 217, 218, 220, 222, 223
PC-Karte .............................................................................................. 244
PCMCIA-Karte ..................................................................................... 244
PDM ..................................................................................................... 244
PDO ..................................................................................................... 245
PDU ..................................................................................................... 245
PERIOD ............................................................................................... 188
PES ...................................................................................................... 245
PGN ..................................................................................................... 245
PID-Regler ........................................................................................... 245
Piktogramm .......................................................................................... 245
Pre-Op ................................................................................................. 245
Prinzipschaltung .................................................................................... 12
Programmierhinweise für CODESYS-Projekte ..................................... 35
Programmiersystem einrichten .............................................................. 46
Programmiersystem manuell einrichten ................................................ 46
Programmiersystem über Templates einrichten ................................... 50
Prozessabbild ...................................................................................... 246
PWM .................................................................................................... 246
PWM1000 ............................................................................................ 196
PWM-Ausgänge ..................................................................................... 59
R
ratiometrisch ........................................................................................ 246
RAW-CAN ............................................................................................ 246
Reaktion abhängig von Betriebsart des Ausgangs ............................... 21
Reaktion auf Fehlermeldungen ........................................................... 225
Reaktion bei Einsatz von PWM oder CURRENT_CONTROL .............. 21
Reaktion der Ausgänge auf Überlast oder Kurzschluss ....................... 21
remanent .............................................................................................. 246
Retain-Variablen .................................................................................... 62
ro .......................................................................................................... 246
RTC ...................................................................................................... 246
Rücklesen von Retain-Variablen ........................................................... 62
RUN-Zustand ......................................................................................... 39
rw ......................................................................................................... 247
S
SAE J1939 ........................................................................................... 247
Schnelle Eingänge ................................................................................. 56
Schnittstellen-Beschreibung .................................................................. 31
Schutzfunktionen der Ausgänge ........................................................... 20
SD-Card ............................................................................................... 247
SDO ..................................................................................................... 247
Selbsttest ............................................................................................. 247
SET_BAR............................................................................................. 211
SET_DIGIT_TO_ALPHA ..................................................................... 213
SET_DIGIT_TO_NUM ......................................................................... 215
SET_DISPLAY_4_DIGIT ..................................................................... 217
2018-07-10