Grundfos DMH 28X Installationsanleitung Seite 4

English (GB) Installation and operating instructions
Original installation and operating instructions
CONTENTS
1. General information
1.1 Introduction
1.2 Applications
2. Safety
2.1 Identification of safety instructions in this manual
2.2 Qualification and training of personnel
2.3 Risks when safety instructions are not observed
2.4 Safety-conscious working
2.5 Safety instructions for the operator/user
2.6 Safety instructions for maintenance, inspection and
installation work
2.7 Unauthorised modification and manufacture of spare
parts
2.8 Improper operating methods
2.9 Safety of the system in the event of a failure in the
dosing system
3. Technical data
3.1 Identification
3.2 Pump models and pump types
3.3 Pump performance
3.4 Sound pressure level
3.5 Electrical data
3.6 AR control unit
3.7 Required energy
3.8 Ambient and operating conditions
3.9 Dosing medium
4. Transport and storage
4.1 Delivery
4.2 Unpacking
4.3 Intermediate storage
4.4 Return
5. Product description and accessories
5.1 General description
5.2 Dimensions
5.3 Weight
5.4 Stroke volume
5.5 Materials
5.6 Data of contact pressure gauge for diaphragm leakage
detection (optional)
6. Installation
6.1 General information on installation
6.2 Installation location
6.3 Mounting
6.4 Approximate values when using pulsation dampers
6.5 Optimum installation
6.6 Installation tips
6.7 Pipe lines
6.8 Connecting the suction and discharge lines
7. Electrical connections
7.1 Electric servomotor (optional)
7.2 Electronic preselection counter (optional)
7.3 Electrically heated dosing head (optional)
7.4 Diaphragm controller (optional)
7.5 Connecting the power supply cable
8. Start-up/shutdown
8.1 Initial start-up/subsequent start-up
8.2 Start-up/subsequent start-up of DMH 280
8.3 Start-up/subsequent start-up of DMH 281-288
8.4 Setting the pressure relief valve
8.5 Zero point adjustments (DMH 281-288)
8.6 Operating the pump
8.7 Shutdown
9. Operation
9.1 Switching on/off
9.2 Setting the dosing capacity
9.3 Deaeration
9.4 Using the AR control unit (optional)
4
9.5 Electric servomotor (optional)
9.6 Electronic preselection counter (optional)
9.7 Electrically heated dosing head (optional)
10. Maintenance
Page
10.1 General notes
4
10.2 Diaphragm leakage control for diaphragm leakage
4
detection
4
10.3 Cleaning and maintenance intervals
5
10.4 Checking the oil level
5
10.5 Cleaning the suction and discharge valves
5
10.6 Replacing the diaphragm and gear oil for dosing head
with single diaphragm (no diaphragm leakage
5
detection)
5
10.7 Replacing the diaphragm for dosing head with double
5
diaphragm
5 11. Fault finding chart
12. Dosing curves
6
13. Disposal
6
Warning
6
Prior to installation, read these installation and
6
operating instructions. Installation and operation
6
must comply with local regulations and accepted
8
codes of good practice.
8
9
1. General information
9
10
1.1 Introduction
10
10 These installation and operating instructions contain all the
11 information required for starting up and handling the DMH 28X
piston diaphragm dosing pump.
11
If you require further information or if any problems arise, which
11
are not described in detail in this manual, please contact the
11
nearest Grundfos company.
11
11
1.2 Applications
12
The DMH 28X pump is suitable for liquid, non-abrasive and
12
non-flammable media strictly in accordance with the instructions
16
in this manual.
17
17
Explosion-proof pumps are identified from the pump
17
and motor nameplates. An EC declaration of
conformity is provided in accordance with the EC
17 Note
directive 2014/34/EU, the so-called ATEX directive.
17
This declaration of conformity replaces the
17
declaration of conformity in this manual.
18
18 Warning
18
To operate a pump which has been identified as an
19
explosion-proof pump for the dosing of inflammable
19
media or for operation in potentially explosive
21
operating sites in accordance with the EC directive
21
2014/34/EU, refer to the enclosed manual
"ATEX-approved pumps" in addition to this manual.
22
22
Warning
22
Other applications or the operation of pumps in
22
ambient and operating conditions, which are not
22
approved, are considered improper and are not
22
permitted. Grundfos accepts no liability for any
23
damage resulting from incorrect use.
23
23
25
26
26
27
27
28
28
28
28
28
29
29
29
29
29
29
29
30
30
31
32
35
36
36