Überwachungen - Siemens SINUMERIK 840D sl Handbuch

Maschinen- und Settingdaten
Achsspezifische NC-Maschinendaten
35450 SPIND_OSCILL_TIME_CCW
s Pendelzeit für M4-Richtung
CTEQ
- -
35500 SPIND_ON_SPEED_AT_IPO_START
- Vorschubfreigabe bei Spindel im Sollbereich
CTEQ
- -
35510 SPIND_STOPPED_AT_IPO_START
- Vorschubfreigabe bei Spindel steht
CTEQ
- -
35550 DRILL_VELO_LIMIT
Umdr/min Maximaldrehzahlen für das Gewindebohren
CTEQ
- 6
35590 PARAMSET_CHANGE_ENABLE
- Parametersatzwechsel möglich
CTEQ
- -
2.5.6 Überwachungen
36000 STOP_LIMIT_COARSE
mm, Grad Genauhalt grob
-
- -
36010 STOP_LIMIT_FINE
mm, Grad Genauhalt fein
-
- -
36012 STOP_LIMIT_FACTOR
- Faktor Genauhalt grob/fein und Stillstand
-
- 6
36020 POSITIONING_TIME
s Verzögerungszeit Genauhalt fein
-
- -
36030 STANDSTILL_POS_TOL
mm, Grad Stillstandstoleranz
-
- -
36040 STANDSTILL_DELAY_TIME
s Verzögerungszeit Stillstandsüberwachung
-
- -
2-238
0.5 -
1 0
FALSE -
10000., 10000., 10000., 1
10000., 10000., 10000.
0 0
0.04,0.04,0.04,0.04,0.0 -
4,0.04,0.04...
0.01,0.01,0.01,0.01,0.0 -
1,0.01,0.01...
1.0, 1.0, 1.0, 1.0, 1.0, 0.001
1.0
1.0 -
0.2,0.2,0.2,0.2,0.2,0.2,0 -
.2,0.2,0.2...
0.4 -
SINUMERIK 840D sl, SINAMICS S120, Listen (LIS1sl), 03/2010
A06 S1,Z1
DOUBLE NEW CONF
- 7/2
A03, A06, A10 S1,Z1
BYTE RESET
2 7/2
A03, A06, A10 S1
BOOLEAN RESET
- 7/2
A06, A11, A04 -
DOUBLE NEW CONF
- 7/2
EXP, A05 TE3,A2,S1,Z1
BYTE POWER ON
2 7/2
A05 TE1,A3,B1,G2,S1,Z1
DOUBLE NEW CONF
- 7/2
A05 TE1,A3,B1,D1,G2,S1,Z1
DOUBLE NEW CONF
- 7/2
A05 G1,A3,B1,G2,S1,Z1
DOUBLE NEW CONF
1000.0 7/2
A05 TE1,A3,B1,G2
DOUBLE NEW CONF
- 7/2
A05 G1,A3,D1,G2
DOUBLE NEW CONF
- 7/2
A05 TE1,A3,F1,G2
DOUBLE NEW CONF
- 7/2
 Siemens AG 2010 All Rights Reserved
03/2010
M
M
M
M
M
M
M
M
M
M
M