Siemens SINUMERIK 840D sl Handbuch Seite 198

Maschinen- und Settingdaten
Kanalspezifische NC-Maschinendaten
24694 TRAFO7_EXT_ROT_AX_OFFSET_2
Grad Positionsoffset der ext. Rundachsen für die 7-Achstrafo 2
-
- 3
24695 TRAFO7_EXT_AXIS1_2
- Richtung der 1. externen Rundachse
-
- 3
24700 TRAANG_ANGLE_1
Grad Winkel zwischen kartesischer Achse und realer (schräger)
Achse
-
- -
24710 TRAANG_BASE_TOOL_1
mm Vektor des Basiswerkzeugs für die 1.TRAANG-Transformation DOUBLE
-
- 3
24720 TRAANG_PARALLEL_VELO_RES_1
- Geschwindigkeitsreserve für 1. TRAANG-Transformation
-
- -
24721 TRAANG_PARALLEL_ACCEL_RES_1
- Beschleunigungsreserve der Parallelachse für 1. TRAANG-
Trafo
-
- -
24750 TRAANG_ANGLE_2
Grad Winkel zwischen kartesischer Achse und realer (schräger)
Achse
-
- -
24760 TRAANG_BASE_TOOL_2
mm Vektor des Basiswerkzeugs für die 2.TRAANG-Transformation DOUBLE
-
- 3
24770 TRAANG_PARALLEL_VELO_RES_2
- Geschwindigkeitsreserve für die 2. TRAANG-Transformation
-
- -
24771 TRAANG_PARALLEL_ACCEL_RES_2
- Beschleunigungsreserve der Parallelachse für 2. TRAANG-
Trafo
-
- -
198
0.0, 0.0, 0.0,0.0, 0.0, -
0.0...
0.0, 0.0 , 0.0,0.0, 0.0 , -
0.0...
0.0,0.0,0.0,0.0,0.0,0.0,0 -
.0,0.0,0.0...
0.0, 0.0 , 0.0,0.0, 0.0 , -
0.0...
0.0,0.0,0.0,0.0,0.0,0.0,0 0.0
.0,0.0,0.0...
0.0,0.0,0.0,0.0,0.0,0.0,0 0.0
.0,0.0,0.0...
0.0,0.0,0.0,0.0,0.0,0.0,0 -
.0,0.0,0.0...
0.0, 0.0 , 0.0,0.0, 0.0 , -
0.0...
0.0,0.0,0.0,0.0,0.0,0.0,0 0.0
.0,0.0,0.0...
0.0,0.0,0.0,0.0,0.0,0.0,0 0.0
.0,0.0,0.0...
SINUMERIK 840D sl, SINAMICS S120, Listen (LIS1sl), 03/2010
C07 F2
DOUBLE NEW CONF
- 7/7
C07 F2
DOUBLE NEW CONF
- 7/7
C07 M1
DOUBLE NEW CONF
- 7/7
C07 M1
NEW CONF
- 7/7
C07 M1
DOUBLE NEW CONF
1.0 7/7
C07 M1
DOUBLE NEW CONF
1.0 7/7
C07 M1
DOUBLE NEW CONF
- 7/7
C07 M1
NEW CONF
- 7/7
C07 M1
DOUBLE NEW CONF
1.0 7/7
C07 M1
DOUBLE NEW CONF
1.0 7/7
 Siemens AG 2010 All Rights Reserved
03/2010
U
U
U
U
U
U
U
U
U
U