Kanalspezifische Settingdaten - Siemens SINUMERIK 840D sl Handbuch

Maschinen- und Settingdaten
NC-Settingdaten
41523 SW_CAM_PLUS_TIME_TAB_2
s Vorhaltezeit zu '+'-Schaltpunkten der Nocken 9-16
-
- 8
41524 SW_CAM_MINUS_TIME_TAB_3
s Vorhaltezeit zu '-'-Schaltpunkten den Nocken 17-24
-
- 8
41525 SW_CAM_PLUS_TIME_TAB_3
s Vorhaltezeiten zu '+'-Schaltpunkten der Nocken 17-24
-
- 8
41526 SW_CAM_MINUS_TIME_TAB_4
s Vorhaltezeit zu '-'-Schaltpunkten der Nocken 25-32
-
- 8
41527 SW_CAM_PLUS_TIME_TAB_4
s Vorhaltezeiten zu '+'-Schaltpunkten den Nocken 25-32
-
- 8
41600 COMPAR_THRESHOLD_1
- Schwellwert des 1. Komperators
-
- 8
41601 COMPAR_THRESHOLD_2
- Schwellwert des 2. Komperators
-
- 8
41700 AXCT_SWWIDTH
- Achs-Container Drehungsvorgabe
CTDE
- 16
2.6.2

Kanalspezifische Settingdaten

42000 THREAD_START_ANGLE
Grad Startwinkel bei Gewinde
-
- -
42010 THREAD_RAMP_DISP
mm Beschleunigungsverhalten der Achse beim Gewindeschneiden DOUBLE
-
- 2
2-256
0.0,0.0,0.0,0.0,0.0,0.0,0 -
.0,0.0
0.0,0.0,0.0,0.0,0.0,0.0,0 -
.0,0.0
0.0,0.0,0.0,0.0,0.0,0.0,0 -
.0,0.0
0.0,0.0,0.0,0.0,0.0,0.0,0 -
.0,0.0
0.0,0.0,0.0,0.0,0.0,0.0,0 -
.0,0.0
0.0,0.0,0.0,0.0,0.0,0.0,0 -
.0,0.0
0.0,0.0,0.0,0.0,0.0,0.0,0 -
.0,0.0
0,0,0,0,0,0,0,0,0,0,0,0,0 -32
,0,0,0
0.,0.,0.,0.,0.,0.,0.,0.,0.,0 -
.,0.,0.,0....
-1., -1.,-1., -1.,-1., -1.,- -1.
1., -1....
SINUMERIK 840D sl, SINAMICS S120, Listen (LIS1sl), 03/2010
- N3
DOUBLE SOFORT
- 7/7
- N3
DOUBLE SOFORT
- 7/7
- N3
DOUBLE SOFORT
- 7/7
- N3
DOUBLE SOFORT
- 7/7
- N3
DOUBLE SOFORT
- 7/7
- A4
DOUBLE SOFORT
- 7/7
- A4
DOUBLE SOFORT
- 7/7
- B3
DWORD NEW CONF
32 7/7
- K1
DOUBLE SOFORT
- 7/7
- V1
SOFORT
999999. 7/7
 Siemens AG 2010 All Rights Reserved
03/2010
U
U
U
U
U
U
U
U
U
U