Siemens SINUMERIK 840D sl Handbuch Seite 181

03/2010
21506 TRACLG_SUPPORT_HOR_OFFSET
mm Horizontaler Offset des Lineals bei Centerless-Schleifen
-
- -
21508 TRACLG_VERT_DIR_SUPPORTAX_1
- Vertikal-Komponente des Lineal-Richtungsvektors für Q1
-
- -
21510 TRACLG_HOR_DIR_SUPPORTAX_1
- Horizontal-Komponente des Lineal-Richtungsvektors für Q1
-
- -
21512 TRACLG_VERT_DIR_SUPPORTAX_2
- Vertikal-Komponente des Lineal-Richtungsvektors für Q2
-
- -
21514 TRACLG_HOR_DIR_SUPPORTAX_2
- Horizontal-Komponente des Lineal-Richtungsvektors für Q2
-
- -
21516 TRACLG_SUPPORT_LEAD_ANGLE
Grad Steigungswinkel des Lineals bei Centerless-Schleifen
-
- -
21518 TRACLG_CONTACT_UPPER_LIMIT
mm Obere Berührgr. des Lineals mit Schleifteil bei Centerl.-Schl.
-
- -
21520 TRACLG_CONTACT_LOWER_LIMIT
mm Untere Berührgr. des Lineals mit Schleifteil bei Centerl.-Schl.
-
- -
21522 TRACLG_GRINDSPI_NR
- Definition der Schleifspindel für Centerless-Schleifen
-
- -
21524 TRACLG_CTRLSPI_NR
- Definition der Regelspindel für Centerless-Schleifen
-
- -
 Siemens AG 2010 All Rights Reserved
SINUMERIK 840D sl, SINAMICS S120, Listen (LIS1sl), 03/2010
0.,0.,0.,0.,0.,0.,0.,0.,0.,0 -
.,0.,0.,0....
1.,1.,1.,1.,1.,1.,1.,1.,1.,1 -
.,1.,1.,1....
0.,0.,0.,0.,0.,0.,0.,0.,0.,0 -
.,0.,0.,0....
0.,0.,0.,0.,0.,0.,0.,0.,0.,0 -
.,0.,0.,0....
1.,1.,1.,1.,1.,1.,1.,1.,1.,1 -
.,1.,1.,1....
0.,0.,0.,0.,0.,0.,0.,0.,0.,0 -90.
.,0.,0.,0....
0.,0.,0.,0.,0.,0.,0.,0.,0.,0 -
.,0.,0.,0....
0.,0.,0.,0.,0.,0.,0.,0.,0.,0 -
.,0.,0.,0....
2,2,2,2,2,2,2,2,2,2,2,2,2 1
,2,2,2
1,1,1,1,1,1,1,1,1,1,1,1,1 1
,1,1,1
Maschinen- und Settingdaten
Kanalspezifische NC-Maschinendaten
C07 S8
DOUBLE POWER ON
- 7/2
C07 -
DOUBLE POWER ON
- 7/2
C07 -
DOUBLE POWER ON
- 7/2
C07 -
DOUBLE POWER ON
- 7/2
C07 -
DOUBLE POWER ON
- 7/2
C07 -
DOUBLE POWER ON
90. 7/2
C07 -
DOUBLE POWER ON
- 7/2
C07 -
DOUBLE POWER ON
- 7/2
C07 -
BYTE POWER ON
20 7/2
C07 -
BYTE POWER ON
20 7/2
M
M
M
M
M
M
M
M
M
M
181