DAMMANN DT 2800H S4 Original Bedienungsanleitung Seite 172

Störungsbeseitigung
SPN FMI DTC Fehler
Beschreibung
524280 2 F8FFE2 Remote Accelerator
Pedal Idle Validation
Switch inputs reversed
524280 3 F8FFE3 Remote Accelerator
Pedal Idle Validation
Switch 1 circuit shorted
to Ubat
524280 4 F8FFE4 Remote Accelerator
Pedal Idle Validation
Switch 1 circuit shorted
to GND
524280 5 F8FFE5 Remote Accelerator
Pedal Idle Validation
Switch 2 circuit shorted
to Ubat
524280 6 F8FFE6 Remote Accelerator
Pedal Idle Validation
Switch 2 circuit shorted
to GND
524281 9 F9FFE9 J1939 Powertrain
Message (Engine
Droop Control) is
missing
524283 2 FBFFE2 Generator (Charging
System) terminal W –
Low Voltage
Seite 308
Fehler Behebung Fault
location
Check wiring of associated pins. Check Pin 2/11
Parameters 13/08, 13/09, 13/10 and Pin 2/14
13/65 Pin 2/13
Pin 2/15
Check wiring of associated pins. Pin 2/11
Check parameter 13/09 (2 14 DI or
Selection) and parameter 13/65 (2 11 DI Pin 2/14
Selection)
Check parameter 13/47 (2 11 Diflex10
Fault Detect Enable) for correct
configuration of Fault Detection of
pin 2/11 and parameter 13/50 (2 14
Diflex13 Fault Detect Enable) for correct
configuration of Fault Detection of pin
2/14
Check wiring of associated pins. Pin 2/11
Check parameter 13/09 (2 14 DI or
Selection) and parameter 13/65 (2 11 DI Pin 2/14
Selection)
Check parameter 13/47 (2 11 Diflex10
Fault Detect Enable) for correct
configuration of Fault Detection of
pin 2/11 and parameter 13/50 (2 14
Diflex13 Fault Detect Enable) for correct
configuration of Fault Detection of pin
2/14
Check wiring of associated pins. Pin 2/13
Check parameter 13/08 (2 13 DI or
Selection) and parameter 13/10 (2 15 DI Pin 2/15
Selection)
Check parameter 13/49 (2 13 Diflex12
Fault Detect Enable) for correct
configuration of Fault Detection of
pin 2/13 and parameter 13/51 (2 15
Diflex14 Fault Detect Enable) for correct
configuration of Fault Detection of pin
2/15
Check wiring of associated pins. Pin 2/13
Check parameter 13/08 (2 13 DI or
Selection) and parameter 13/10 (2 15 DI Pin 2/15
Selection)
Check parameter 13/49 (2 13 Diflex12
Fault Detect Enable) for correct
configuration of Fault Detection of
pin 2/13 and parameter 13/51 (2 15
Diflex14 Fault Detect Enable) for correct
configuration of Fault Detection of pin
2/15
Check J1939 link connection
Check wiring of Generator Terminal W or
check Generator functionality
Erstellt im: Mai 2020
®
SPN FMI
524283 14
524284 14
524284 19
524285 4
524286 1
524286 2
524286 3
524286 4
524286 5
524286 6
524286 7
Erstellt im: Mai 2020
®
DTC Fehler Fehler Behebung
Beschreibung
FBFFEE Generator (Charging Check wiring of Generator Terminal W or
System) terminal W – check Generator functionality
allocation error (pulse /
rev signal)
FCFFEE PMC Level 2 fault Change CPC4
(limitation occured)
FCFFF3 PMC Level 3 General PMC Level 3 General Protection Fault
Protection Fault (either Black Channel Message counter
(either Black Channel or CRC is wrong)
Message counter or
CRC is wrong)
FDFFE4 CM1 DPF Check parameter 01/07 (CM1 DPF
Regeneration Switch Source Addr SAE J1939) for correct
configuration
shorted to GND (if
applied more than 5
sec this error flags)
FEFFE1 Automatic gear Check MCM, ACM, TCM and CPC
selection: automatic Failure (calibration wrong)
mode is not available
(multiple causes for
error: AT is in manual
mode, no automatic
mode possible)
Check if CAL-Dataset version fits
FEFFE2 Automatic gear
selection: incompatible to the software version, engine and
or missing dataset transmission type
(calibration error,
wrong calibration data
set for this vehicle)
FEFFE3 Automatic gear Check MCM, ACM, TCM and CPC
selection: EcoRoll is Failure
not available (multiple
errors, no EcoRoll
available)
FEFFE4 Automatic gear Check MCM, ACM, TCM and CPC
selection: Gear shift Failure
not plausible (multiple
errors, no optimal gear
shift possible)
FEFFE5 Automativ gear Check TCM for proper function and fault
selection: No gear codes. Possible gearbox error.
shiftable.
FEFFE6 ITPM error: vehicle Check parameterization of PTCONF
calibration is (PGR 048)
inconsistent
FEFFE7 ITPM error: drivetrain Check parameterization of PTCONF
speed signal is (PGR 048)
inconsistent. (One or Check signals as follows:
more speed signals -engine speed
incorrect) -transmission input speed
-transmission output speed
-TCO vehicle speed
-ABS/EBS vehicle speed
Störungsbeseitigung
Fault
location
Seite 309