DAMMANN DT 2800H S4 Original Bedienungsanleitung Seite 162

Störungsbeseitigung
SPN FMI DTC Fehler
Beschreibung
709 4 C50204 Digital Output 3/16
Circuit shorted to GND
709 5 C50205 Digital Output 3/16
Open Circuit (broken
wire, terminal floating)
710 3 C60203 Digital Output 4/06
Circuit shorted to Ubat
710 4 C60204 Digital Output 4/06
Circuit shorted to GND
710 5 C60205 Digital Output 4/06
Open Circuit (broken
wire, terminal floating)
Seite 288
Fehler Behebung Fault
location
Check wiring of associated pin Pin 3/16
Check parameters 35/11 (Selection),
35/30 (Fault Detection) and 35/47
(Configuration) for correct configuration
of output pin 3/16
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 5
Check wiring of associated pin Pin 3/16
Check parameters 35/11 (Selection),
35/30 (Fault Detection) and 35/47
(Configuration) for correct configuration
of output pin 3/16
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 5
Check wiring of associated pin Pin 4/06
Check parameters 35/15 (Selection),
35/34 (Fault Detection) and 35/51
(Configuration) for correct configuration
of output pin 4/06
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 6
Check wiring of associated pin Pin 4/06
Check parameters 35/15 (Selection),
35/34 (Fault Detection) and 35/51
(Configuration) for correct configuration
of output pin 4/06
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 6
Check wiring of associated pin Pin 4/06
Check parameters 35/15 (Selection),
35/34 (Fault Detection) and 35/51
(Configuration) for correct configuration
of output pin 4/06
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 6
Erstellt im: Mai 2020
®
SPN FMI
711 3
711 4
711 5
712 3
712 4
Erstellt im: Mai 2020
®
DTC Fehler Fehler Behebung
Beschreibung
C70203 Digital Output 1/05 Check wiring of associated pin
Circuit shorted to Ubat Check parameters 35/02 (Selection),
35/21 (Fault Detection) and 35/39
(Configuration) for correct configuration
of output pin 1/05
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 12
C70204 Digital Output 1/05 Check wiring of associated pin
Circuit shorted to GND Check parameters 35/02 (Selection),
35/21 (Fault Detection) and 35/39
(Configuration) for correct configuration
of output pin 1/05
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 12
C70205 Digital Output 1/05 Check wiring of associated pin
Open Circuit (broken Check parameters 35/02 (Selection),
wire, terminal floating)
35/21 (Fault Detection) and 35/39
(Configuration) for correct configuration
of output pin 1/05
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 12
C80203 Digital Output 1/04 Check wiring of associated pin
Circuit shorted to Ubat Check parameters 35/01 (Selection),
35/20 (Fault Detection) and 35/38
(Configuration) for correct configuration
of output pin 1/04
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 13
C80204 Digital Output 1/04 Check wiring of associated pin
Circuit shorted to GND Check parameters 35/01 (Selection),
35/20 (Fault Detection) and 35/38
(Configuration) for correct configuration
of output pin 1/04
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 13
Störungsbeseitigung
Fault
location
Pin 1/05
Pin 1/05
Pin 1/05
Pin 1/04
Pin 1/04
Seite 289