DAMMANN DT 2800H S4 Original Bedienungsanleitung Seite 166

Störungsbeseitigung
SPN FMI DTC Fehler
Beschreibung
1623 13 57060D J1939 Tachograph
Output Shaft Speed
Signal is missing or not
available = SNA (signal
not available)
1624 9 580609 J1939 TCO1 Message
is missing or not
available
1624 13 58060D J1939 Tachograph
Vehicle Speed Signal
is missing or not
available = SNA (signal
not available) + J1939
TCO1 speed sensor
selected
1624 19 580613 J1939 Tachograph
Vehicle Speed Signal
is erractic = undefined
value but not SNA +
J1939 TCO1 speed
sensor selected
1663 7 7F0607 Optimized idle
prevented from
resuming (Safety Loop
Faulted)
1681 9 910609 J1939 BM Message
(Battery Main Switch)
is missing
1716 9 B40609 J1939 ERC1 Message
is missing or not
available
1716 13 B4060D Evobus 5stage retarder
level calibration not
plausible
1814 9 160709 J1939 VDC1 Message
was not received or
has stopped arriving.
1845 9 350709 J1939 TCFG2
Message is missing or
not available
2003 9 D30709 J1939 Message is
missing from source
adress 3 (3dec =
Transmission #1 ECU
missing)
2011 9 DB0709 J1939 Message is
missing from source
address 11 (dec).
Seite 296
Fehler Behebung Fault
location
Check wiring of associated pin
Check J1939 link connection to Vehicle
Speed Sensor. Check Parameter 08/13
(Vehicle Speed Sensor Configuration) for
proper configuration
Check J1939 link connection to Vehicle
Speed Sensor. Check Parameter 08/13
(Vehicle Speed Sensor Configuration) for
proper configuration
Check J1939 link connection to Vehicle
Speed Sensor. Check Parameter 08/13
(Vehicle Speed Sensor Configuration) for
proper configuration
Check if Park brake is applied, Engine
Hood is Closed and Transmission is in
Neural Position.
Check the wiring of the involved switches
and sensors.
Check J1939 link connection
Check J1939 link connection to Retarder
Check wiring of associated pin. Pin 2/13
Check parameters 13/08 (Selection) and
13/49 (Fault Detect Enable) for correct
configuration of input pin 2/13.
Check J1939 link connection. Check
Parameter 01/57 (VDC1 Source Adress
SAE J1939)
Check J1939 link connection to
Transmission Control
Check J1939 link connection to Cruise
Control ECU
Erstellt im: Mai 2020
®
SPN FMI
2017 9
2023 9
2025 9
2033 9
2042 9
2049 9
2596 9
2623 2
2623 8
Erstellt im: Mai 2020
®
DTC Fehler Fehler Behebung
Beschreibung
E10709 J1939 Message is Check J1939 link connection to Cruise
missing from source Control ECU
address 17 (17dec =
Cruise Control ECU
missing)
E70709 J1939 Message is Check J1939 link connection to
missing from source Instrument Cluster ECU
23 (23dec = Instrument
Cluster ECU missing)
E90709 J1939 Message is Check J1939 link connection to
missing from source 25 Passenger Operator Climate Control
(25dec = Passenger- ECU
Operator Climate
Control ECU missing)
F10709 J1939 Message is Check J1939 link connection to body
missing from source Controller ECU
33 (33dec = Body
Controller ECU
missing)
FA0709 J1939 Message is Check J1939 link connection to Headway
missing from source Controller ECU
42 (42dec = Headway
Controller (forward-
looking collision
warning, collision
avoidance, speed
Controller, or speed
matching) ECU is
missing)
10809 J1939 Message is Check J1939 link connection to Gab
missing from source Controller – Primary ECU
49 (49dec = Gab
Controller - Primary
ECU missing)
240A09 J1939 CM1 Message Check J1939 link connection
(Maximum Vehicle
Speed Limit) is Missing
or Not Available
3F0A02 2-Channel Accelerator Check wiring of associated pins and
Pedal "in-range" fault calibration; Restart learning routine.
(AP Ch1 and Ch2 (chapter 6.4, routines 1 to 3):
values differ to much)
Check Accelerator Pedal for proper
behavier regarding voltage of the 2
channels.
3F0A08 2-Channel Accelerator Check wiring of associated pin
Pedal Signal 2 Missing
Störungsbeseitigung
Fault
location
Pin 1/06
Seite 297