DAMMANN DT 2800H S4 Original Bedienungsanleitung Seite 171

Störungsbeseitigung
SPN FMI DTC Fehler
Beschreibung
3873 4 210F04 Analog Output 02
shorted to GND or
Circuit Open (broken
wire, terminal floating)
3948 9 6C0F09 J1939 PTODE
Message (PTO
Drive Engagement)
is missing or not
available
4041 0 C90F00 Indication of a critical
software (logic) failure.
(20ms ECU OS Task
Locked in an Endless
Loop)
4041 9 C90F09 Indication of a
critical resource
allocation issue. Task
restructuring required.
(20ms ECU OS Task
Timed out Prior to
Completion)
4041 16 C90F10 Indication of a critical
software (logic) failure.
(1000ms ECU OS Task
Locked in an Endless
Loop)
4206 2 6E1002 TSC1 Message
Counter indicates lost
Messages
4207 2 6F1002 TSC1 Message
Checksum wrong
524275 19 F3FFF3 RCM Message not
received or stopped
arriving
524276 13 F4FFED MCM fuelmap to GVC
emission standard
calibration (02/23)
mismatched
524277 13 F5FFED Super Structure Cabin
Mode ENABLE-State
ERROR
Seite 306
Fehler Behebung Fault
location
Check wiring of associated pin. Pin 3/06
Check parameters 09/04 (Selection)
and 09/10 (Fault Detection) for correct
configuration of output pin 3/06.
Run Service Routine (chapter 6.4,
routines 8 to 10):
– Analog Output Pin Under Software
Control: Start with Signal Parameter 6,
Frequency in Hz, Width in %
Check J1939 link connection
Check Parameter 01/108 (PTODE
Source Address SAE J1939)
Try reprogramming the CPC with the
new software release.
Replace CPC4 and reprogram with the
latest software.
Try reprogramming the CPC with the
new software release.
Replace CPC4 and reprogram with the
latest software.
Try reprogramming the CPC with the
new software release.
Replace CPC4 and reprogram with the
latest software.
Try reprogramming the CPC with the
new software release.
Replace CPC4 and reprogram with the
latest software.
Try reprogramming the CPC with the
new software release.
Replace CPC4 and reprogram with the
latest software.
Check CPC4 PT-CAN link connection.
Check RCM functionality / PT-CAN link
connection
Check parameter 02/24 (GVC Emission
Standard Conf) for correct setting.
Check CPC4 PT-CAN link connection.
Check if vehicle speed has plausible
value. Check park brake state. Check if
gearbox sends valid values for current
and selected gear. Check if CC is
deactivated.
Erstellt im: Mai 2020
®
SPN FMI
524277 14
524277 19
524278 13
524278 14
524278 15
524279 2
524279 3
524279 4
524279 11
524279 18
Erstellt im: Mai 2020
®
DTC Fehler Fehler Behebung
Beschreibung
F5FFEE Driving from Check CPC4 PT-CAN link connection.
SuperStructure Check engine mode. Check service
IMPLAUSIBLE brake state. Check if gearbox sends valid
Condition values for current and selected gear.
Check if CC is deactivated.
F5FFF3 Super Structure Cabin Check CPC4 PT-CAN link connection.
Mode DISABLE-State Check if vehicle speed has plausible
ERROR value. Check park brake state. Check if
gearbox sends valid values for current
and selected gear. Check if CC is
deactivated.
F6FFED 2-Channel RAT Check wiring of associated pins.
Accelerator Pedal Check parameter 09/01 (1 9 FPO_02
Signal 1 Missing Selection) and parameter 09/06 (4 12
FPO_01 Selection)
Check parameter 09/12 (4 12 FPO_01
Fault Detection) for correct configuration
of Fault Detection of pin 4/12 and
parameter 09/08 (1 9 FPO_02 Fault
Detection) for correct configuration
of Fault Detection of pin 1/09. Check
parameter 09/14 (1 9 FPO_02 Resistor
Enable) for pin 1/09 resistor activation.
F6FFEE 2-Channel RAT Check wiring of associated pins.
Accelerator Pedal Check parameter 09/01 (1 9 FPO_02
Signal 2 Missing Selection) and parameter 09/06 (4 12
FPO_01 Selection)
Check parameter 09/12 (4 12 FPO_01
Fault Detection) for correct configuration
of Fault Detection of pin 4/12 and
parameter 09/08 (1 9 FPO_02 Fault
Detection) for correct configuration
of Fault Detection of pin 1/09. Check
parameter 09/14 (1 9 FPO_02 Resistor
Enable) for pin 1/09 resistor activation.
F6FFEF RAT Accelerator pedal Deviation between RAT Ch1 and Ch2 too
„in-range" fault. high. Check RAT AP Sensor.
F7FFE2 Expansion tank Check wiring of associated pins.
pressure sensor data Check parameter 13/63 (3 04 AI_02
erratic Selection) and parameter 13/64 (4 14
AI_03 Selection)
F7FFE3 Expansion tank Check wiring of associated pins.
pressure sensor circuit Check parameter 13/63 (3 04 AI_02
shorted to Ubat Selection) and parameter 13/64 (4 14
AI_03 Selection)
F7FFE4 Expansion tank Check wiring of associated pins.
pressure sensor circuit Check parameter 13/63 (3 04 AI_02
shorted to GND Selection) and parameter 13/64 (4 14
AI_03 Selection)
F7FFEB Expansion Pressure Inspect Expansion Pressure Tank for
Tank Pressure Set leaks
Fault
F7FFF2 Expansion Pressure Inspect Expansion Pressure Tank for
Tank Pressure Loss leaks
Störungsbeseitigung
Fault
location
Pin 4/12
Pin 1/09
Pin 4/12
Pin 1/09
Pin 3/04
Pin 4/14
Pin 3/04
Pin 4/14
Pin 3/04
Pin 4/14
Seite 307