DAMMANN DT 2800H S4 Original Bedienungsanleitung Seite 160

Störungsbeseitigung
SPN FMI DTC Fehler
Beschreibung
702 5 BE0205 Digital Output 3/08
Open Circuit (broken
wire, terminal floating)
703 3 BF0203 Digital Output 3/09
Circuit shorted to Ubat
703 4 BF0204 Digital Output 3/09
Circuit shorted to GND
703 5 BF0205 Digital Output 3/09
Open Circuit (broken
wire, terminal floating)
704 3 C00203 Digital Output 4/07
Circuit shorted to Ubat
Seite 284
Fehler Behebung Fault
location
Check wiring of associated pin Pin 3/08
Check parameters 35/07 (Selection),
35/26 (Fault Detection) and 35/43
(Configuration) for correct configuration
of output pin 3/08
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 10
Check wiring of associated pin Pin 3/09
Check parameters 35/08 (Selection),
35/27 (Fault Detection) and 35/44
(Configuration) for correct configuration
of output pin 3/09
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 14
Check wiring of associated pin Pin 3/09
Check parameters 35/08 (Selection),
35/27 (Fault Detection) and 35/44
(Configuration) for correct configuration
of output pin 3/09
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 14
Check wiring of associated pin Pin 3/09
Check parameters 35/08 (Selection),
35/27 (Fault Detection) and 35/44
(Configuration) for correct configuration
of output pin 3/09
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 14
Check wiring of associated pin Pin 4/07
Check parameters 35/16 (Selection),
35/35 (Fault Detection) and 35/52
(Configuration) for correct configuration
of output pin 4/07
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 15
Erstellt im: Mai 2020
®
SPN FMI
704 4
704 5
705 3
705 4
705 5
Erstellt im: Mai 2020
®
DTC Fehler Fehler Behebung
Beschreibung
C00204 Digital Output 4/07 Check wiring of associated pin
Circuit shorted to GND Check parameters 35/16 (Selection),
35/35 (Fault Detection) and 35/52
(Configuration) for correct configuration
of output pin 4/07
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Dvigital Output Pin Under Software
Control: Start Response with Signal
Parameter 15
C00205 Digital Output 4/07 Check wiring of associated pin
Open Circuit (broken Check parameters 35/16 (Selection),
wire, terminal floating)
35/35 (Fault Detection) and 35/52
(Configuration) for correct configuration
of output pin 4/07
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 15
C10203 Digital Output 1/13 Check wiring of associated pin
Circuit shorted to Ubat Check parameters 35/03 (Selection),
35/22 (Fault Detection) and 35/40
(Configuration) for correct configuration
of output pin 1/13
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 1
C10204 Digital Output 1/13 Check wiring of associated pin
Circuit shorted to GND Check parameters 35/03 (Selection),
35/22 (Fault Detection) and 35/40
(Configuration) for correct configuration
of output pin 1/13
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 1
C10205 Digital Output 1/13 Check wiring of associated pin
Open Circuit (broken Check parameters 35/03 (Selection),
wire, terminal floating)
35/22 (Fault Detection) and 35/40
(Configuration) for correct configuration
of output pin 1/13
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 1
Störungsbeseitigung
Fault
location
Pin 4/07
Pin 4/07
Pin 1/13
Pin 1/13
Pin 1/13
Seite 285