DAMMANN DT 2800H S4 Original Bedienungsanleitung Seite 163

Störungsbeseitigung
SPN FMI DTC Fehler
Beschreibung
712 5 C80205 Digital Output 1/04
Open Circuit (broken
wire, terminal floating)
713 7 C90207 TOP2 Shift Failure
714 3 CA0203 Digital Output 4/10
Circuit shorted to Ubat
714 4 CA0204 Digital Output 4/10
Circuit shorted to GND
714 5 CA0205 Digital Output 4/10
Open Circuit (broken
wire, terminal floating)
715 3 CB0203 Frequency Output 4/12
Circuit shorted to Ubat
Seite 290
Fehler Behebung Fault
location
Check wiring of associated pin Pin 1/04
Check parameters 35/01 (Selection),
35/20 (Fault Detection) and 35/38
(Configuration) for correct configuration
of output pin 1/04
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 13
Check wiring of associated pin Pin 3/07
Check parameters 35/06 (Selection),
35/25 (Fault Detection) and 35/42
(Configuration) for correct configuration
of output pin 3/07
Check wiring of associated pin Pin 4/10
Check parameters 35/18 (Selection),
35/37 (Fault Detection) and 35/54
(Configuration) for correct configuration
of output pin 4/10
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 11
Check wiring of associated pin Pin 4/10
Check parameters 35/18 (Selection),
35/37 (Fault Detection) and 35/54
(Configuration) for correct configuration
of output pin 4/10
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 11
Check wiring of associated pin Pin 4/10
Check parameters 35/18 (Selection),
35/37 (Fault Detection) and 35/54
(Configuration) for correct configuration
of output pin 4/10
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 11
Check wiring of associated pin Pin 4/12
Run Service Routine (chapter 6.4,
routines 8 to 10):
– Analog Output Pin Under Software:
Start with Signal Parameter 1, Frequency
in Hz, Width in %
Erstellt im: Mai 2020
®
SPN FMI
715 4
715 5
716 3
716 4
716 5
904 9
904 13
904 19
924 3
Erstellt im: Mai 2020
®
DTC Fehler Fehler Behebung
Beschreibung
CB0204 Frequency Output 4/12 Check wiring of associated pin
Circuit shorted to GND Run Service Routine (chapter 6.4,
routines 8 to 10):
– Analog Output Pin Under Software:
Start with Signal Parameter 1, Frequency
in Hz, Width in %
CB0205 Frequency Output 4/12 Check wiring of associated pin
Open Circuit (broken Run Service Routine (chapter 6.4,
wire, terminal floating)
routines 8 to 10):
– Analog Output Pin Under Software:
Start with Signal Parameter 1, Frequency
in Hz, Width in %
CC0203 Frequency Output 1/09 Check wiring of associated pin
Circuit shorted to Ubat Run Service Routine (chapter 6.4,
routines 8 to 10):
– Analog Output Pin Under Software:
Start with Signal Parameter 2, Frequency
in Hz, Width in %
CC0204 Frequency Output 1/09 Check wiring of associated pin
Circuit shorted to GND Run Service Routine (chapter 6.4,
routines 8 to 10):
– Analog Output Pin Under Software:
Start with Signal Parameter 2, Frequency
in Hz, Width in %
CC0205 Frequency Output 1/09 Check wiring of associated pin
Open Circuit (broken Run Service Routine (chapter 6.4,
wire, terminal floating)
routines 8 to 10):
– Analog Output Pin Under Software:
Start with Signal Parameter 2, Frequency
in Hz, Width in %
880309 J1939 EBC2 Message Check J1939 link connection to the ABS
from ABS is missing and Devices Brake System Controller
or not available = SNA
(signal not available)
88030D J1939 Front Axle Check J1939 link connection to Front
Speed Signal is Axle Speed Sensor
missing or not
available = SNA (signal
not available)
880313 J1939 Front Axle Check J1939 link connection to Front
Speed Signal is erratic Axle Speed Sensor
= undefined value but
not SNA
9C0303 Digital Output 4/09 Check wiring of associated pin
Circuit shorted to Ubat Check parameters 35/17 (Selection),
35/36 (Fault Detection) and 35/53
(Configuration) for correct configuration
of output pin 4/09
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 7
Störungsbeseitigung
Fault
location
Pin 4/12
Pin 4/12
Pin 1/09
Pin 1/09
Pin 1/09
Pin 4/09
Seite 291