Inhaltsverzeichnis
Werbung
Störungsbeseitigung
SPN
FMI
DTC
Fehler
Beschreibung
973
19
CD0313
J1939 Engine Retarder
Selection Signal
erractic = undefined
value but not SNA
974
2
CE0302
Remote Accelerator
Pedal Supply Voltage
Out of Range
974
3
CE0303
Remote Accelerator
Pedal Circuit shorted
to Ubat
974
4
CE0304
Remote Accelerator
Pedal Circuit shorted
to GND
979
9
D30309
J1939 PTO Message
Not Received This
Ignition Cycle
986
9
DA0309
J1939 CM1 DPF
Message is missing or
not available
986
13
DA030D
J1939 CM1 Fan
SPN986 Signal from
source address #1
or #2 is missing or
not available = SNA
(signal not available)
986
19
DA0313
J1939 CM1 Fan
SPN986 Signal from
source address #1
or #2 is erractic =
undefined value but
not SNA
1089
9
410409
J1939 AIR1 Message
(Air Supply Pressure)
is missing from first
source address
1089
13
41040D
J1939 AIR1 Message
(Air Supply Pressure)
is missing from second
source address
1121
2
610402
J1939 Powertrain
Message (AMT –
Detroit transmission) is
missing
1121
13
61040D
J1939 Service Brake
Switch Signal from
EBC1 is missing or not
available = SNA (signal
not available)
Seite 294
Fehler Behebung
Fault
location
Check J1939 link connection to Engine
Retarder
Check wiring of associated pins
Pin 3/03
Pin 3/04
Check wiring of associated pins
Pin 3/02
Pin 3/03
Pin 3/04
Check wiring of associated pins
Pin 3/02
Pin 3/03
Pin 3/04
Check J1939 link connection.
Check Parameter 01/52 (PTO Source
Adress SAE J1939) for proper
configuration.
Check J1939 link connection and
Devices Cab Controller 1 and Climate
Control.
Check Parameter 01/07 (CM1 DPF
Source Adress SAE J1939) for proper
configuration.
Check J1939 link connection.
Check Parameter 01/08 (CM1 Fan
Source Adress #1 SAE J1939) and
Parameter 01/09 (CM1 Fan Source
Adress #2 SAE J1939) for proper
configuration.
Check J1939 link connection.
Check Parameter 01/08 (CM1 Fan
Source Adress #1 SAE J1939) and
Parameter 01/09 (CM1 Fan Source
Adress #2 SAE J1939) for proper
configuration.
Check J1939 link connection
Check Parameter 01/96 (AIR1 Source
Address 1 SAE J1939)
Check J1939 link connection
Check Parameter 01/102 (AIR1 Source
Address 2 SAE J1939)
Check wiring of J2CC and related J1939
link connection
Check J1939 link connection to Service
Brake. Check Parameter 01/10 (EBC1
Source Adress SAE J1939)
Erstellt im: Mai 2020
®
SPN
FMI
1121
19
1237
4
1243
14
1482
9
1484
9
1484
13
1590
9
1590
19
1592
9
1592
13
1592
19
1623
9
Erstellt im: Mai 2020
®
DTC
Fehler
Fehler Behebung
Beschreibung
610413
J1939 Service Brake
Check J1939 link connection to Service
Switch Signal from
Brake. Check Parameter 01/10 (EBC1
EBC1 is erractic =
Source Adress SAE J1939)
undefined value but
not SNA
D50404
Stop Engine Override
Check wiring of associated pin.
Switch shorted to
Check parameters 13/04 (Selection) and
Ground (if applied
13/41 (Fault Detect Enable) for correct
configuration of input pin 1/15.
more than 5 sec this
error flags)
DB040E
ABS fault restricts
Check ABS for proper function.
automatic gear
Combination of ABS and ASC error. ABS
selection functionality.
error = v > 1km/h and req-gear < current
gear and ABS in stat "not fully operable"
CA0509
J1939 TC1 Message
Check J1939 link connection to
(Transmission Mode) is
Transmission Control
missing
CC0509
J1939 Message was
Check J1939 link connection
lost (Message Counter
Error)
CC050D
J1939 Message was
Check J1939 link connection
lost (CRC Error)
360609
Adaptive Cruise
Check J1939 link connection. J1939 ACC
Control Message Not
Message not received.
Received
360613
Adaptive Cruise
Adaptive Cruise Control – General Error.
Control – General
Disables ACC feature.
Error
380609
J1939 HRW Message
Check J1939 link connection to ABS.
Check correct configuration (parameter
from ABS is missing
(HRW not received
02/09 (Transmission Type)) if newAMT
in case newAMT
Transmission is used
Transmission used)
38060D
J1939 HRW Wheel
Check J1939 link connection to ABS.
Check correct configuration (parameter
Speed Signal Missing
(HRW received but at
02/09 (Transmission Type)) if newAMT
least one signal not
Transmission is used
available)
380613
J1939 HRW Wheel
Check J1939 link connection to ABS.
Check correct configuration (parameter
Speed Signal
Erroneous (HRW
02/09 (Transmission Type)) if newAMT
received but at least
Transmission is used
one signal erroneous)
570609
J1939 Tachograph
Check wiring of associated pin
Output Shaft Speed
Signal is erratic =
undefined value but
not SNA
Störungsbeseitigung
Fault
location
Pin 1/15
Seite 295
Werbung
Inhaltsverzeichnis
