DAMMANN DT 2800H S4 Original Bedienungsanleitung Seite 167

Störungsbeseitigung
SPN FMI DTC Fehler
Beschreibung
2646 3 560A03 Digital Output 4/02
Circuit shorted to Ubat
2646 4 560A04 Digital Output 4/02
Circuit shorted to GND
2646 5 560A05 Digital Output 4/02
Open Circuit (broken
wire, terminal floating)
Off-Highway Engine
2882 13 420B0D
Configuration Selection
message on J1939
was not received or
has stopped arriving.
2900 9 540B09 J1939 ETC7 Message
is missing or not
available
3187 9 730C09 Transmission Shift
Console Datalink (LIN)
3353 2 190D02 Generator (Charging
System) D+ terminal
failure
3510 4 B60D04 Accelerator Pedal
Supply Voltage Circuit
shorted to GND
3510 7 B60D07 Accelerator Pedal
Supply Voltage Circuit
shorted to Ubat
3511 3 B70D03 Remote Accelerator
Pedal Supply Voltage
circuit shorted to Ubat
Seite 298
Fehler Behebung Fault
location
Check wiring of associated pin Pin 4/02
Check parameters 35/14 (Selection),
35/33 (Fault Detection) and 35/50
(Configuration) for correct configuration
of output pin 4/02
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 9
Check wiring of associated pin Pin 4/02
Check parameters 35/14 (Selection),
35/33 (Fault Detection) and 35/50
(Configuration) for correct configuration
of output pin 4/02
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 9
Check wiring of associated pin Pin 4/02
Check parameters 35/14 (Selection),
35/33 (Fault Detection) and 35/50
(Configuration) for correct configuration
of output pin 4/02
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 9
Check the J1939 link connection
Check parameter 01/72 for configuration
of OHECS source address
Check parameter 05/06 for proper
configuration
Check J1939 link connection to
Transmission Controller / Check if
Electronic Transmission Controller is
CAN capable
Check LIN wiring / stalk switch
Check wiring of Generator Terminal D+
or check Generator functionality
Check wiring of associated pins Pin 1/08
Pin 3/03
Check wiring of associated pins Pin 1/08
Pin 3/03
Check wiring of associated pins Pin 3/03
(Supply)
Pin 3/02
(GND)
Erstellt im: Mai 2020
®
SPN FMI
3511 4
3606 9
3645 9
3695 9
3695 13
3695 14
3695 19
3696 4
3696 9
3696 13
3696 14
3696 19
Erstellt im: Mai 2020
®
DTC Fehler Fehler Behebung
Beschreibung
B70D04 Remote Accelerator Check wiring of associated pins
Pedal Supply Voltage
circuit shorted to GND
160E09 J1939 PROP04 Check J1939 link connection to Diesel
Message is missing or Particulate Filter
not available
3D0E09 J1939 TCI Message Check J1939 link connection
(Transfer Case
Information) is missing
6F0E09 J1939 DPF Regen Check J1939 link connection to Diesel
Inhibit MUX Switch Particulate Filter.
Message Stopped Check Parameter 46/10 (DPF J1939
Arriving Inhibt Sw Enable) and 46/11 (DPF J1939
Regen Sw Enable).
6F0E0D J1939 DPF Regen Check J1939 link connection to Diesel
Inhibit MUX Switch Particulate Filter.
Message Contains Check Parameter 46/10 (DPF J1939
SNV(SNA) Indicator Inhibt Sw Enable) and 46/11 (DPF J1939
Regen Sw Enable).
6F0E0E J1939 DPF Regen Check J1939 link connection to Diesel
Inhibit MUX Switch Particulate Filter.
Message Not Received Check Parameter 46/10 (DPF J1939
this Ignition Cycle Inhibt Sw Enable) and 46/11 (DPF J1939
Regen Sw Enable).
6F0E13 J1939 DPF Regen Check J1939 link connection to Diesel
Inhibit MUX Switch Particulate Filter.
Message Contains Check Parameter 46/10 (DPF J1939
Data Error(erractic) Inhibt Sw Enable) and 46/11 (DPF J1939
Indicator Regen Sw Enable).
700E04 J1939 DPF Check J1939 link connection to Diesel
Regeneration Switch Particulate Filter.
Circuit shorted to GND Check Parameter 46/10 (DPF J1939
(if applied more than 5 Inhibt Sw Enable) and 46/11 (DPF J1939
sec this error flags)
Regen Sw Enable).
700E09 J1939 DPF Regen Check J1939 link connection to Diesel
Force MUX Switch Particulate Filter.
Message Stopped Check Parameter 46/10 (DPF J1939
Arriving Inhibt Sw Enable) and 46/11 (DPF J1939
Regen Sw Enable).
700E0D J1939 DPF Regen Check J1939 link connection to Diesel
Force MUX Switch Particulate Filter.
Message Contains Check Parameter 46/10 (DPF J1939
SNV(SNA) Indicator Inhibt Sw Enable) and 46/11 (DPF J1939
Regen Sw Enable).
700E0E J1939 DPF Regen Check J1939 link connection to Diesel
Force MUX Switch Particulate Filter.
Message Not Received Check Parameter 46/10 (DPF J1939
this Ignition Cycle Inhibt Sw Enable) and 46/11 (DPF J1939
Regen Sw Enable).
700E13 J1939 DPF Regen Check J1939 link connection to Diesel
Force MUX Switch Particulate Filter.
Message Contains Check Parameter 46/10 (DPF J1939
Data Error(erractic) Inhibt Sw Enable) and 46/11 (DPF J1939
Indicator Regen Sw Enable).
Störungsbeseitigung
Fault
location
Pin 3/03
(Supply)
Pin 3/02
(GND)
Seite 299