DAMMANN DT 2800H S4 Original Bedienungsanleitung Seite 159

Störungsbeseitigung
SPN FMI DTC Fehler
Beschreibung
625 14 71020E PTCAN: MCM Sytem
ID Not Received or
Stopped Arriving
(ECAN ID_596/7 not
received or it has
stopped arriving)
628 2 740202 EEPROM Checksum
Failure
628 12 74020C EEPROM Checksum
Failure for the SCR
Block
628 14 74020E XFLASH Static Fault
Code Memory Page
Read Write Failure
(XFLASH Failure.)
628 17 740211 1000ms ECU OS Task
Timed out Prior to
Completion. (Indication
of a critical resource
allocation issue. Task
restructuring required.)
629 2 750202 CPC Hardware /
Software Mismatch
(Incorrect Hardware
Configuration - NAFTA
Vs. EUROPE)
DDEC Data Xflash
629 12 75020C
Write Error. Replace
CPC. (XFLASH
Failure.)
630 13 76020D SCR Number out Of
Range
639 9 7F0209 J1939 PROP11
message no longer
received within it's
expected time.
639 13 7F020D HDMS Fan is
configured and the
J1939 message was
not received or has
stopped arriving.
639 14 7F020E J1939 Data Link
Failure (CPC is no
longer sending or
receiving data from the
J1939 link.)
667 3 9B0203 Starter Pin 1/18 Circuit
shorted to Ubat (KL50)
Seite 282
Fehler Behebung Fault
location
Check PT-CAN link connection.
Check MCM functionality / PT-CAN link
connection
Try reprogramming the CPC with the
new software release. Reset EEPROM
values to default. Redownload CPC
parameter set.
Replace CPC4 and reprogram with the
latest software.
FUSO only. None. To be checked
PEP. Replace modul if this failure occurs
again.
Replace CPC4 box due to XFLASH
failure and reprogram with the latest
software.
Try reprogramming the CPC with the
new software release.
Replace CPC4 and reprogram with the
latest software.
Try reprogramming the CPC with the
new software release. Reset EEPROM
values to default. Redownload CPC
parameter set.
Replace CPC4 and reprogram with the
latest software.
Try reprogramming the CPC with the
new software release.
Replace CPC4 and reprogram with the
latest software.
FUSO only. Reset EEPROM values to
default. Redownload CPC.
Use SPN default values. SA Parameter
01/17 (FUSO ISS Source Addr SAE
J1939)
Check J1939 link connection to the air
conditioner transducer. Check if CPC4
parameters correct for the vehicle
configuration.
Check J1939 data link connection Pin 2/16
Pin 2/17
Pin 2/18
Check KL50 wiring at Pin 1/18 Pin 1/18
Erstellt im: Mai 2020
®
SPN FMI
701 3
701 4
701 5
702 3
702 4
Erstellt im: Mai 2020
®
DTC Fehler Fehler Behebung
Beschreibung
BD0203 Digital Output 3/07 Check wiring of associated pin
Circuit shorted to Ubat Check parameters 35/06 (Selection),
35/25 (Fault Detection) and 35/42
(Configuration) for correct configuration
of output pin 3/07
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 9
BD0204 Digital Output 3/07 Check wiring of associated pin
Circuit shorted to GND Check parameters 35/06 (Selection),
35/25 (Fault Detection) and 35/42
(Configuration) for correct configuration
of output pin 3/07
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 9
BD0205 Digital Output 3/07 Check wiring of associated pin
Open Circuit (broken Check parameters 35/06 (Selection),
wire, terminal floating)
35/25 (Fault Detection) and 35/42
(Configuration) for correct configuration
of output pin 3/07
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 9
BE0203 Digital Output 3/08 Check wiring of associated pin
Circuit shorted to Ubat Check parameters 35/07 (Selection),
35/26 (Fault Detection) and 35/43
(Configuration) for correct configuration
of output pin 3/08
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 10
BE0204 Digital Output 3/08 Check wiring of associated pin
Circuit shorted to GND Check parameters 35/07 (Selection),
35/26 (Fault Detection) and 35/43
(Configuration) for correct configuration
of output pin 3/08
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 10
Störungsbeseitigung
Fault
location
Pin 3/07
Pin 3/07
Pin 3/07
Pin 3/08
Pin 3/08
Seite 283