DAMMANN DT 2800H S4 Original Bedienungsanleitung Seite 158

Störungsbeseitigung
SPN FMI DTC Fehler
Beschreibung
596 19 540213 J1939 Cruise Control
Enable Switch Signal
from Source CCVS1,
CCVS2 or CCVS3
erractic = undefined
value but not SNA
597 2 550202 Service Brake Status
Not Plausible
597 13 55020D J1939 Service Brake
Switch Signal from
Source CCVS1,
CCVS2 or CCVS3
missing or not
available = SNA
(signal not available)
597 19 550213 J1939 Service Brake
Switch Signal from
Source CCVS1,
CCVS2 or CCVS3
erractic = undefined
value but not SNA
598 2 560202 Clutch switch status
not plausible
599 4 570204 Cruise Control SET
and RESUME Circuits
shorted to GND (SET
and RESUME applied
at the same time)
600 13 58020D J1939 Cruise Control
Coast Switch Signal
from Source CCVS1,
CCVS2 or CCVS3
missing or not
available = SNA (signal
not available)
600 19 580213 J1939 Cruise Control
Coast Switch Signal
from Source CCVS1,
CCVS2 or CCVS3
erractic = undefined
value but not SNA
Seite 280
Fehler Behebung Fault
location
Check J1939 link connection to Cruise
Control
Check Parameter 13/22 (CC ON OFF
Switch Config) for correct source
Check Parameter 01/04 (CC1 Source
Adress SAE J1939), 01/05 (CC2 Source
Adress SAE J1939) and 01/06 (CC3
Source Adress SAE J1939) for correct
Source Adress
FUSO Only.
Check J1939 link connection to Cruise
Control
Check Parameter 13/29 (Service Brake
Switch Config) for correct source
Check Parameter 01/04 (CC1 Source
Adress SAE J1939), 01/05 (CC2 Source
Adress SAE J1939) and 01/06 (CC3
Source Adress SAE J1939) for correct
Source Adress
Check J1939 link connection to Cruise
Control
Check Parameter 13/29 (Service Brake
Switch Config) for correct source
Check Parameter 01/04 (CC1 Source
Adress SAE J1939), 01/05 (CC2 Source
Adress SAE J1939) and 01/06 (CC3
Source Adress SAE J1939) for correct
Source Adress
Check wiring of Clutch Switch and
Driveline Open Status
Check wiring of associated pins Pin 1/12
Pin 1/16
Check J1939 link connection to Cruise
Control
Check Parameter 13/24 (CC Set Cst Res
Accel Sw Config) for correct source
Check Parameter 01/04 (CC1 Source
Adress SAE J1939), 01/05 (CC2 Source
Adress SAE J1939) and 01/06 (CC3
Source Adress SAE J1939) for correct
Source Adress
Check J1939 link connection to Cruise
Control
Check Parameter 13/24 (CC Set Cst Res
Accel Sw Config) for correct source
Check Parameter 01/04 (CC1 Source
Adress SAE J1939), 01/05 (CC2 Source
Adress SAE J1939) and 01/06 (CC3
Source Adress SAE J1939) for correct
Source Adress
Erstellt im: Mai 2020
®
SPN FMI
602 13
602 19
608 14
609 12
609 13
609 16
625 2
625 4
625 8
625 9
625 13
Erstellt im: Mai 2020
®
DTC Fehler Fehler Behebung
Beschreibung
5A020D J1939 Cruise Control Check J1939 link connection to Cruise
Accelerator Switch Control
Signal from Source Check Parameter 13/24 (CC Set Cst Res
Accel Sw Config) for correct source
CCVS1, CCVS2 or
CCVS3 = SNA (signal Check Parameter 01/04 (CC1 Source
not available) Adress SAE J1939), 01/05 (CC2 Source
Adress SAE J1939) and 01/06 (CC3
Source Adress SAE J1939) for correct
Source Adress
5A0213 J1939 Cruise Control Check J1939 link connection to Cruise
Accelerator Switch Control
from Source CCVS1, Check Parameter 13/24 (CC Set Cst Res
Accel Sw Config) for correct source
CCVS2 or CCVS3
erractic = undefined
Check Parameter 01/04 (CC1 Source
value but not SNA Adress SAE J1939), 01/05 (CC2 Source
Adress SAE J1939) and 01/06 (CC3
Source Adress SAE J1939) for correct
Source Adress
60020E J1708 Data Link Fault is active IF j1708_g_
Failure TransFaultValFlag_u1 AND j1708_g_
TransFaultFlag_u1 are TRUE
61020C CPC electronics are Try reprogramming the CPC with the
defect (EEPROM, new software release.
CPU...) Replace CPC4 and reprogram with the
latest software.
Source address setting conflict.
61020D the CPC SW is corrupt
(CPC Software Messages with more than one source
Diagnostics) address (e.g. "CM1 Fan Source Addr1"
and "CM1 Fan Source Addr2") have to be
parameterized with different addresses.
Check calibration for these addresses
(PGR 01 "Communication")
610210 Internal temperature of Check CPC4 case and cooling
measurements. Turn off vehicle.
CPC4 too high.
710202 PTCAN Incorrect MCM MCM Sys ID not valid (MCM initialization
not finished). Check MCM.
System ID received
710204 ECAN Link Circuit ECAN Hardware Link Failure. Check
Failure Engine Controller, Check engine can
circuitry
710208 MCM PT-CAN DM1 Check CPC4 PT-CAN link connection.
Message Not Received Check MCM functionality / PT-CAN link
or has Stopped connection
Arriving
710209 ACM PT-CAN DM1 Check CPC4 PT-CAN link connection.
Message Not Received Check ACM functionality / PT-CAN link
or has Stopped connection
Arriving
71020D TCM System ID Not Check CPC4 PT-CAN link connection.
Received or Stopped Check TCM functionality / PT-CAN link
Arriving (TCM Outage connection
-> Check Translamp)
Störungsbeseitigung
Fault
location
Seite 281