DAMMANN DT 2800H S4 Original Bedienungsanleitung Seite 170

Störungsbeseitigung
SPN FMI DTC Fehler
Beschreibung
3863 4 170F04 Digital Input 4/17
Circuit shorted to GND
3864 3 180F03 Digital Input 3/18
Circuit shorted to Ubat
3864 4 180F04 Digital Input 3/18
Circuit shorted to GND
3865 3 190F03 Digital Input 4/08
Circuit shorted to Ubat
3865 4 190F04 Digital Input 4/08
Circuit shorted to GND
3866 3 1A0F03 Digital Input 4/04
Circuit shorted to Ubat
3866 4 1A0F04 Digital Input 4/04
Circuit shorted to GND
3867 3 1B0F03 Digital Input 4/05
Circuit shorted to Ubat
3867 4 1B0F04 Digital Input 4/05
Circuit shorted to GND
3868 3 1C0F03 Digital Input 4/03
Circuit shorted to Ubat
3868 4 1C0F04 Digital Input 4/03
Circuit shorted to GND
3869 3 1D0F03 Digital Input 4/01
Circuit shorted to Ubat
3869 4 1D0F04 Digital Input 4/01
Circuit shorted to GND
Seite 304
Fehler Behebung Fault
location
Check wiring of associated pin Pin 4/17
Check parameters 13/18 (Selection),
13/61 (Fault Detect Ena) for correct
configuration of input pin 4/17
Check wiring of associated pin Pin 3/18
Check parameters 13/12 (Selection),
13/52 (Fault Detect Ena) for correct
configuration of input pin 3/18
Check wiring of associated pin Pin 3/18
Check parameters 13/12 (Selection),
13/52 (Fault Detect Ena) for correct
configuration of input pin 3/18
Check wiring of associated pin Pin 4/08
Check parameters 13/16 (Selection),
13/58 (Fault Detect Ena) for correct
configuration of input pin 4/08
Check wiring of associated pin Pin 4/08
Check parameters 13/16 (Selection),
13/58 (Fault Detect Ena) for correct
configuration of input pin 4/08
Check wiring of associated pin Pin 4/04
Check parameters 13/14 (Selection),
13/56 (Fault Detect Ena) for correct
configuration of input pin 4/04
Check wiring of associated pin Pin 4/04
Check parameters 13/14 (Selection),
13/56 (Fault Detect Ena) for correct
configuration of input pin 4/04
Check wiring of associated pin Pin 4/05
Check parameters 13/15 (Selection),
13/57 (Fault Detect Ena) for correct
configuration of input pin 4/05
Check wiring of associated pin Pin 4/05
Check parameters 13/15 (Selection),
13/57 (Fault Detect Ena) for correct
configuration of input pin 4/05
Check wiring of associated pin Pin 4/03
Check parameters 13/13 (Selection),
13/55 (Fault Detect Ena) for correct
configuration of input pin 4/03
Check wiring of associated pin Pin 4/03
Check parameters 13/13 (Selection),
13/55 (Fault Detect Ena) for correct
configuration of input pin 4/03
Check wiring of associated pin Pin 4/01
Check parameter 13/53 (Fault Detect
Ena) for correct configuration of Fault
Detection of pin 4/01
Check wiring of associated pin Pin 4/01
Check parameter 13/53 (Fault Detect
Ena) for correct configuration of Fault
Detection of pin 4/01
Erstellt im: Mai 2020
®
SPN FMI
3870 3
3870 4
3871 3
3871 4
3871 5
3872 3
3872 4
3873 3
Erstellt im: Mai 2020
®
DTC Fehler Fehler Behebung
Beschreibung
1E0F03 Digital Input 4/02 Check wiring of associated pin
Circuit shorted to Ubat Check parameter 13/54 (Fault Detect
Ena) for correct configuration of Fault
Detection of pin 4/02
1E0F04 Digital Input 4/02 Check wiring of associated pin
Circuit shorted to GND Check parameter 13/54 (Fault Detect
Ena) for correct configuration of Fault
Detection of pin 4/02
1F0F03 Transmission Speed Check wiring of associated pin
Sensor 4/04 or 3/13
Circuit shorted to Ubat
1F0F04 Transmission Speed Check wiring of associated pin
Sensor 4/04 or 3/13
Circuit shorted to GND
1F0F05 Transmission Speed Check wiring of associated pin
Sensor Circuit Open
(broken wire, terminal
floating)
200F03 Analog Output 01 Check wiring of associated pin.
shorted to Ubat Check parameters 09/03 (Selection)
and 09/09 (Fault Detection) for correct
configuration of output pin 3/05.
Run Service Routine (chapter 6.4,
routines 8 to 10):
– Analog Output Pin Under Software
Control: Start with Signal Parameter 5,
Frequency in Hz, Width in %
200F04 Analog Output 01 Check wiring of associated pin.
shorted to GND or Check parameters 09/03 (Selection)
Circuit Open (broken and 09/09 (Fault Detection) for correct
wire, terminal floating) configuration of output pin 3/05.
Run Service Routine (chapter 6.4,
routines 8 to 10):
– Analog Output Pin Under Software
Control: Start with Signal Parameter 5,
Frequency in Hz, Width in %
210F03 Analog Output 02 Check wiring of associated pin.
shorted to Ubat Check parameters 09/04 (Selection)
and 09/10 (Fault Detection) for correct
configuration of output pin 3/06.
Run Service Routine (chapter 6.4,
routines 8 to 10):
– Analog Output Pin Under Software
Control: Start with Signal Parameter 6,
Frequency in Hz, Width in %
Störungsbeseitigung
Fault
location
Pin 4/02
Pin 4/02
Pin 4/04 or
3/13
Pin 4/04 or
3/13
Pin 4/04 or
3/13
Pin 3/05
Pin 3/05
Pin 3/06
Seite 305