Inhaltsverzeichnis
Werbung
Störungsbeseitigung
SPN
FMI
DTC
Fehler
Beschreibung
111
3
6F0003
Coolant Level Circuit
shorted to Ubat
111
4
6F0004
Coolant Level Sensor
Circuit Failed Low
111
6
6F0006
Coolant Level Sensor
Circuit shorted to GND
111
18
6F0012
Coolant Level below
operating level (pre-
warning condition)
120
13
78000D
J1939 Retarder Fluid
Message is missing or
not available (J1939
Cabin Message
is missing or not
available?)
158
2
9E0002
KL15 ignition switch
status of CPC and
MCM do not match.
168
0
A80000
Battery Voltage High
168
1
A80001
Battery Voltage Very
Low
168
7
A80007
Opt Idle Detected
Charging System or
Battery Failure
168
9
A80009
Main battery
connection lost
168
14
A8000E
ECU powerdown
not completed (Main
Battery Terminal
Possibly Floating)
168
18
A80012
Battery Voltage Low
Seite 276
Fehler Behebung
Fault
location
Check wiring of associated pins
Pin 3/02
(GND)
Pin 3/11
(Supply)
Check wiring of associated pins
Pin 3/02
(GND)
Pin 3/11
(Supply)
Check wiring of associated pins
Pin 3/02
(GND)
Pin 3/11
(Supply)
Check coolant level in reservoir. If
coolant level is not within limit, refill
coolant to proper level. If it is within
proper level, change coolant level
sensor. Check coolant leak at cylinder
head gasket, coolant leak at air
compressor head gasket, external
coolant leak at hose connections, coolant
in oil, loose or faulty radiator cap, heating
system for leaks.
Check J1939 link connection to
transmission retarder
Check KL15 wiring at Pin 2/03
Pin 2/03
Check Voltage KL15 and KL30 (Fault
Pin 2/01
Condition Battery Voltage > 35V)
Pin 2/03
Check wiring of associated pins
Check Voltage KL15 and Kl30 (Fault
Pin 2/01
Condition Battery Voltage < 9.8V)
Pin 2/03
Check wiring of associated pins
If vehicle Is equipped with a battery
disconnect switch, it must be inspected
Check battery main switch and battery
Pin 2/01
wiring (KL30)
Pin 2/03
Check battery main switch and battery
Pin 2/01
wiring (KL30)
Pin 2/03
Check wiring of associated pins
Pin 2/01
If vehicle Is equipped with a battery
Pin 2/03
disconnect switch, it must be inspected
Check Voltage KL15 and KL30 (Fault
Pin 2/01
Condition Battery Voltage < 19.2V)
Pin 2/03
Check wiring of associated pins
Erstellt im: Mai 2020
®
SPN
FMI
171
2
171
3
171
4
171
9
171
14
187
3
187
4
191
9
191
13
191
19
247
0
247
1
247
9
Erstellt im: Mai 2020
®
DTC
Fehler
Fehler Behebung
Beschreibung
AB0002
Ambient Temperature
Check ambient temperature sensor
Sensor Data Erratic
(wiring and associated pin)
Check parameter 31/01 (Ambient
Air Temp Sensor Enable) for correct
configuration of Ambient Temperature
Sensor
AB0003
Ambient Temperature
Check ambient temperature sensor
Sensor shorted to Ubat
(wiring and associated pin)
Check parameter 31/01 (Ambient
Air Temp Sensor Enable) for correct
configuration of Ambient Temperature
Sensor
AB0004
Ambient Temperature
Check ambient temperature sensor
Sensor shorted to
(wiring and associated pin)
GND
Check parameter 31/01 (Ambient
Air Temp Sensor Enable) for correct
configuration of Ambient Temperature
Sensor
AB0009
J1587 Ambient Air
Check J1939 link connection to ambient
Temp Sensor Data
Air Temp Sensor and wiring. Check
Message Stopped
Parameter 31/01 (Ambient Air Temp
Sensor Enable) for proper configuration.
Arriving
AB000E
J1587 Ambient Air
Check J1939 link connection to ambient
Temp Sensor Data
Air Temp Sensor and wiring. Check
Not Received This Ign
Parameter 31/01 (Ambient Air Temp
Sensor Enable) for proper configuration.
Cycle
BB0003
Idle Volume Sensor
FUSO Idle Volume Switch circuit shorted
circuit shorted to Ubat
to Ubat
BB0004
Idle Volume Sensor
FUSO Idle Volume Switch circuit shorted
circuit shorted to GND
to GND
BF0009
J1939 ETC1 Message
Check J1939 link connection to
is missing or not
Transmission Controller / Check if
available
Electronic Transmission Controller is
CAN capable
BF000D
J1939 Transmission
Check J1939 link connection to
Output Shaft Speed
Transmission Controller / Check if
Signal is missing or not
electronic Transmission Controller is
available = SNA (signal
CAN capable
not available)
BF0013
J1939 Transmission
Check J1939 link connection to
Output Shaft Speed
Transmission Controller
Signal erractic =
undefined value but
not SNA
F70000
MCM Engine Hours
Check MCM.
Data higher than
expected
F70001
MCM Engine Hours
CPC or MCM. The internal clocks of the
Data lower than
CPC or MCM do not match. Check MCM.
expected
F70009
MCM Engine Hours
Check MCM.
Data not received or
stopped arriving
Störungsbeseitigung
Fault
location
Pin 3/15
Pin 3/15
Pin 3/15
Pin 3/15
Pin 3/15
Seite 277
Werbung
Inhaltsverzeichnis
