DAMMANN DT 2800H S4 Original Bedienungsanleitung Seite 164

Störungsbeseitigung
SPN FMI DTC Fehler
Beschreibung
924 4 9C0304 Digital Output 4/09
Circuit shorted to GND
924 5 9C0305 Digital Output 4/09
Open Circuit (broken
wire, terminal floating)
925 3 9D0303 Digital Output 3/17
Circuit shorted to Ubat
925 4 9D0304 Digital Output 3/17
Circuit shorted to GND
925 5 9D0305 Digital Output 3/17
Open Circuit (broken
wire, terminal floating)
Seite 292
Fehler Behebung Fault
location
Check wiring of associated pin Pin 4/09
Check parameters 35/17 (Selection),
35/36 (Fault Detection) and 35/53
(Configuration) for correct configuration
of output pin 4/09
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 7
Check wiring of associated pin Pin 4/09
Check parameters 35/17 (Selection),
35/36 (Fault Detection) and 35/53
(Configuration) for correct configuration
of output pin 4/09
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 7
Check wiring of associated pin Pin 3/17
Check parameters 35/12 (Selection),
35/31 (Fault Detection) and 35/48
(Configuration) for correct configuration
of output pin 3/17
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 8
Check wiring of associated pin Pin 3/17
Check parameters 35/12 (Selection),
35/31 (Fault Detection) and 35/48
(Configuration) for correct configuration
of output pin 3/17
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 8
Check wiring of associated pin Pin 3/17
Check parameters 35/12 (Selection),
35/31 (Fault Detection) and 35/48
(Configuration) for correct configuration
of output pin 3/17
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 8
Erstellt im: Mai 2020
®
SPN FMI
926 3
926 4
926 5
970 3
970 4
972 2
973 2
973 9
973 13
Erstellt im: Mai 2020
®
DTC Fehler Fehler Behebung
Beschreibung
9E0303 Digital Output 4/01 Check wiring of associated pin
Circuit shorted to Ubat Check parameters 35/13 (Selection),
35/32 (Fault Detection) and 35/49
(Configuration) for correct configuration
of output pin 4/01
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 16
9E0304 Digital Output 4/01 Check wiring of associated pin
Circuit shorted to GND Check parameters 35/13 (Selection),
35/32 (Fault Detection) and 35/49
(Configuration) for correct configuration
of output pin 4/01
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 16
9E0305 Digital Output 4/01 Check wiring of associated pin
Open Circuit (broken Check parameters 35/13 (Selection),
wire, terminal floating)
35/32 (Fault Detection) and 35/49
(Configuration) for correct configuration
of output pin 4/01
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 16
CA0303 Engine Aux. Shutdown Check wiring of associated pin.
Input shorted to Ubat Check parameters 13/03 (Selection)
and 13/35 (Fault Detection) for correct
configuration of input pin 1/01.
CA0304 Engine Aux. Shutdown Check wiring of associated pin.
Input shorted to GND Check parameters 13/03 (Selection)
and 13/35 (Fault Detection) for correct
configuration of input pin 1/01.
CC0302 Throttle inhibit switch Check wiring of associated pin.
signal not plausible Check parameters 13/05 (Selection)
due to excess vehicle and 13/43 (Fault Detection) for correct
configuration of input pin 1/17.
speed
CD0302 Evobus 5stage Check wiring of associated pin.
retarder level position Check parameters 13/08 (Selection)
not plausible and 13/49 (Fault Detection) for correct
configuration of input pin 2/13.
CD0309 J1939 EBC1 Message Check J1939 link connection and
is missing or not Devices Turbocharger.
available Check Parameter 01/10 (EBC1 Source
Adress SAE J1939)
CD030D J1939 Engine Check J1939 link connection to Engine
Retarder Selection Retarder
Signal Missing or not
available = SNA (signal
not available)
Störungsbeseitigung
Fault
location
Pin 4/01
Pin 4/01
Pin 4/01
Pin 1/10
Pin 1/10
Pin 1/17
Pin 2/13
Seite 293