DAMMANN DT 2800H S4 Original Bedienungsanleitung Seite 157

Störungsbeseitigung
SPN FMI DTC Fehler
Beschreibung
247 10 F7000A MCM Engine Hours
Data increasing at an
implausible rate
247 14 F7000E ACM Reported Ash
Mileage is Lower then
the CPC Stored Value
523 13 0B020D J1939 Transmission
Current Gear Signal
is missing or not
available
523 19 0B0213 J1939 Transmission
Current Gear Signal
is erractic = undefined
value but not SNA
524 9 0C0209 J1939 ETC2 message
is missing or not
available
525 7 0D0207 Transmission gear
selection switch
reports internal error.
525 9 0D0209 J1939 Powertrain
Message (transfer
case / PTO) is missing
525 19 0D0213 Transmission gear
selection switch
reports unplausible
engine brake stage
requests.
527 9 0F0209 J1939 CCVS is
missing or not
available
556 9 2C0209 J1939 RC Message
from Transmission
Retarder is missing
558 2 2E0202 Idle Validation Switch
Inputs Reversed.
Seite 278
Fehler Behebung Fault
location
CPC or MCM. The internal clocks of the
CPC or MCM do not match. Check MCM.
Use diagnostic service to clear the ash
content value.
Check J1939 link connection to
Transmission
Check J1939 link connection to
Transmission
Check J1939 link connection to
Transmission Controller / Check if
Electronic Transmission Controller is
CAN capable
Check J1939 link connection to
Transmission Controller / Check if
Electronic Transmission Controller is
CAN capable.
Check LIN wiring / stalk switch.
Check wiring of OEM ICU and related
J1939 link connection
Check J1939 link connection to
Transmission Controller / Check if
Electronic Transmission Controller is
CAN capable.
Check LIN wiring / stalk switch.
Check J1939 link connection to Cruise
Control
Check Parameter 13/22 (CC ON OFF
Switch Config) for correct source
Check Parameter 01/04 (CC1 Source
Adress SAE J1939), 01/05 (CC2 Source
Adress SAE J1939) and 01/06 (CC3
Source Adress SAE J1939) for correct
Source Adress
Check J1939 link connection to
Transmission Retarder.
Check if Transmission Retarder is
enabled and correct configured,
Parameter 55/01. (Trans Ret Number of
Stages)
Check Idle Validation switch wiring Pin 1/03
Pin 1/06
Erstellt im: Mai 2020
®
SPN FMI
558 3
558 4
558 5
558 6
569 9
571 4
596 13
Erstellt im: Mai 2020
®
DTC Fehler Fehler Behebung
Beschreibung
2E0203 Idle Validation Switch 1 Check wiring of associated pin
Circuit shorted to Ubat. Check parameters 35/01 (Selection),
The two idle switches 35/20 (Fault Detection) and 35/38
(Configuration) for correct configuration
are not synchron
(check AP) of output pin 1/04
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 13
2E0204 Idle Validation Switch 1 Check wiring of associated pin
Circuit shorted to GND. Check parameters 35/01 (Selection),
The two idle switches 35/20 (Fault Detection) and 35/38
(Configuration) for correct configuration
are not synchron
(check AP) of output pin 1/04
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 13
2E0205 Idle Validation Switch 2 Check wiring of associated pin
Circuit shorted to GND. Check parameters 35/01 (Selection),
The two idle switches 35/20 (Fault Detection) and 35/38
(Configuration) for correct configuration
are not synchron
(check AP) of output pin 1/04
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 13
2E0206 Idle Validation Switch 2 Check wiring of associated pin
Circuit shorted to Ubat. Check parameters 35/01 (Selection),
The two idle switches 35/20 (Fault Detection) and 35/38
(Configuration) for correct configuration
are not synchron
(check AP) of output pin 1/04
Run Service Routine (chapter 6.4,
routines 15 to 17):
– Digital Output Pin Under Software
Control: Start Response with Signal
Parameter 13
390209 J1939 EAC1 Message Check J1939 link connection to
is missing or not Electronic Axle Control
available
3B0204 Engine Brake Disable Check wiring of associated pin
push-button shorted Check parameters 13/19 (Selection),
to Ground or pressed 13/62 (Fault Detect Ena) for correct
configuration of input pin 4/18
too long
54020D J1939 Cruise Control Check J1939 link connection to Cruise
Enable Switch Control
Signal from Source Check Parameter 13/22 (CC ON OFF
Switch Config) for correct source
CCVS1, CCVS2 or
CCVS3 missing or not Check Parameter 01/04 (CC1 Source
available = SNA (signal Adress SAE J1939), 01/05 (CC2 Source
not available) Adress SAE J1939) and 01/06 (CC3
Source Adress SAE J1939) for correct
Source Adress
Störungsbeseitigung
Fault
location
Pin 1/04
Pin 1/04
Pin 1/04
Pin 1/04
Pin 4/18
Seite 279